Question about Cars & Trucks

Open Question

Hi tractor model is a McCormick MC 95,when he attaches his Kvernland round bale rapper,the ram which controls the cutting and holding the wrap PAUL....

The ram which cuts and holds the wrap for next bale,will not return??.The rams return is completed by a heavy duty spring!.Since changing tractor to a McCormick MC 95,this problem has arose??. Any help appreciated!!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: trucks cuts off wont hold code

Your vehicle may be involved in recall 07S57 for camshaft postion sensor replacement. It will cause these symptoms you described.
Go this website http://www.genuineservice.com/genuineservice/en/default?page=Home

Look on the left side task bar, pick recalls and insert your complete VIN number to see if your vehicle is involved.

Posted on Feb 14, 2009

Ad
  • 580 Answers

SOURCE: 1999 dodge ram 3500 cut factory trailer wiring

Check out this link www.dodgeram.org/tech/mods/electric/trailer_wire.htm

Posted on Jul 10, 2009

  • 324 Answers

SOURCE: How do you remove hub to replace universal joint

Mark position of drive shaft and yoke - to install in the same position (not to upset balance)
Remove and discard small "U" bolts on yoke Slide drive shaft up spline end to dislodge drive shaft from yoke.
You can either "beat" U join out of shaft, but better to bring to auto parts store that has a machine shop to install new joint
Use new "U" bolts to install
Make sure "U" joint is fully seated in yoke and installed in same position as removed

Posted on Oct 06, 2009

  • 21 Answers

SOURCE: 1999 Avalon check engine light on turns off trac

take to a parts store that offers free code reading. that will tell you the problems

Posted on Mar 29, 2010

roniecon
  • 6927 Answers

SOURCE: AC blower sounds like it is blowing full speed but

sounds like a door actuator motor that is not working,the dash will have to be removed to repair the problem

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New Holland 72 bale thrower will not increase or decrease speed on belts.


From what I've discovered there's a lot of issues a hand---I found a site that has different issues with model---variety of various items contribute to the same problem----you'll have to find you particular issue--there a list of items that may apply to you situation that you'll have to check out---GL

https://www.google.com/search?q=New+Holland+72+bale+thrower&rlz=1C1NHXL_enUS713US714&oq=New+Holland+72+bale+thrower&aqs=chrome..69i57j0l3.2071j0j9&sourceid=chrome&ie=UTF-8#q=control+speed+of+belt+New+Holland+72+bale+thrower

Jul 05, 2017 | Cars & Trucks

2 Answers

How can I become a better rapper?


  1. Practice voice lessons. Rappers are musicians whose voices are their instruments. ...
  2. Rap along to your favorites. ...
  3. Do diction exercises. ...

Mar 28, 2017 | Cars & Trucks

2 Answers

What oil pressure is needed in the rams on the back door which set bale pressure on a krone 1250 round pack


tough question that

http://www.mascus.co.uk/specs/round-balers_985594/krone/round-pack-1250_1024021


Krone Round Pack 1250 Baler, multicut 17 knives, , rotor feed, 15.0/55-17 tyres, bale kicker, 2.0m pick up, wide angle pto c/w cam clutch.


26231542-pydfs01uymjn35d4pjpmt2o5-2-0.jpg

Jul 04, 2016 | Cars & Trucks

1 Answer

How to disable or bypass viper alarm on 95 Honda accord


Older aftermarket alarms can be a real problem. The best thing to do is completely remove it from your car. This isn't too hard, it just takes a little time, I usually charge 1 hour to do it. Locate and remove the control units and disconnect all wires tied into the factory harnesses. Wrap up any exposed wires with electrical tape and reattach any cut wires and wrap up. Take everything out, siren, wires, etc and you will be better off.

Feb 28, 2015 | 1995 Honda Accord

1 Answer

To replace the heater core i have to remove the dash. I am able to remove every thing but a few wire harnesses. they do not have any clips or any thing. how do i remove these? and how do i remove the...


Heater Core REMOVAL & INSTALLATION 1985-95 Models For the removal of the heater core, which is located inside the heater-A/C unit assembly, first remove the heater-A/C unit assembly from the vehicle as described later in this section. Once the unit has been removed, use the following procedure to extract the heater core:
  1. Place the heater-A/C unit on a suitable work surface.
  2. Locate and remove one retaining nut from the blend-air door pivot shaft.
  3. To remove the top cover from the heater-A/C case, the crank arm must be removed.
  4. Disconnect the vacuum lines from the defroster and panel mode vacuum actuators and position them out of the way.
  5. Remove the 3 heater-A/C unit cover attaching screws, fastened upward at the defroster outlet chamber.
  6. Remove the 2 heater-A/C unit cover attaching screws, fastened upward at the air inlet plenum.
  7. Remove the 11 heater-A/C unit cover attaching screws, fastened downward into the housing. Then lift the cover from the heater-A/C unit.
  8. Remove the old heater core from the case. To install:
  9. Install the new heater core into the heater-A/C unit case in the same position as the old one.
  10. Place the cover onto the case and secure in place with the 11 retaining screws.
  11. Install the remaining components in the reverse of the removal procedure.
  12. Install the heater-A/C unit assembly into the vehicle.
---
1989-95 Models EXCEPT DYNASTY AND PREMIER NOTE: The following procedure can be used on all specified 1989-95 models. Slight variations may occur due to extra connections, etc., but the basic procedure should cover all models. Modify the service steps as necessary. Refer to the supplemental restraint system disarming procedure as necessary. NOTE: It is vital to have the A/C system discharged by a reputable automotive technician utilizing a recovery/recycling machine before detaching the A/C system. Refer to the A/C system precautions presented in Section 1.
  1. If the vehicle is equipped with air conditioning, have the A/C system discharged by a qualified professional mechanic, using an approved recovery/recycling machine.
  2. Disconnect the negative battery cable. Drain the cooling system.
  3. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
  4. Disconnect the H-valve connection at the valve and remove the H-valve. Remove the condensation tube.
  5. Remove the glove box, right side kick and sill panels, and all modules, relay panels and computer components in the vicinity of the heater housing.
  6. Remove the lower instrument panel silencers and reinforcements. Remove the radio and other dashboard-mounted optional equipment, as required.
  7. Remove the floor console, if equipped. Remove the floor and defroster distribution ducts.
  8. Remove the bolt holding the right side instrument panel to the right cowl.
  9. Disconnect the blower motor wiring, antenna, resistor wiring and the temperature control cable.
  10. On 1990-95 Daytona and LeBaron models, using a suitable cutting device, cut the instrument panel along the indented line on the padded cover to the right of the glove box opening. Cut only plastic, not metal. Remove the reinforcement and the piece of instrument panel that is riveted to it.
  11. Disconnect the demister hoses from the top of the housing, if equipped.
  12. Disconnect the hanger strap from the package and rotate it aside.
  13. Remove the retaining nuts from the package mounting studs at the fire wall.
  14. Fold the carpeting and insulation back to provide a little more working room and to prevent spillage from staining the carpeting. Pull the right side of the instrument panel out as far as possible.
  15. Remove the heater housing from the dash panel and remove it from the passenger compartment. If the passenger seat is preventing removal, remove it.
  16. To disassemble the housing assembly, remove the retaining screws from the cover and remove the cover.
  17. Remove the retaining screw from the heater core and remove the core from the housing assembly. To install:
  18. Remove the temperature control door from the housing and clean the unit out with solvent. Lubricate the lower pivot rod and its well, then install. Wrap the heater core with foam tape and place it in position. Secure it with its screw.
  19. Assemble the housing, making sure all cover screws were used.
  20. Connect the demister hoses. Install the nuts to the fire wall and connect the hanger strap inside the passenger compartment.
  21. Fold the carpeting back into position.
  22. Install the bolt that attaches the right side of the instrument panel to the cowl.
  23. Connect the blower motor wiring, antenna, resistor wiring and the temperature control cable.
  24. Install the remaining components in the reverse of the removal procedure.
  25. Fill the cooling system.
  26. Connect the negative battery cable and check the entire climate control system for proper operation and leakage.
  27. Have the air conditioning system evacuated and recharged by a qualified professional mechanic utilizing the proper equipment.

Dec 15, 2010 | 1993 Plymouth Sundance

1 Answer

Where is the fuel cutoff switch on a 1983 mercedes 300 D?


the fuel cut-off is a vacuum cut off which is mounted on the rear of the fuel injector. it has a brown vacuum hose attached to it. To check it after it is out you push the plunger in while holding your finger tightly on the vac port to see if it holds pressure. The replacement part is a "BOSCH" #1427133091 for around $100. Many times the failure of the cut-off is not the switch but is in the vacuum system. you can check this by attaching the brown vac hose directly to the vac system at the yellow round check valve right above the cut-off switch.The HAYNES manual #63012 will explaine the systems I described very well.

Aug 31, 2010 | 1983 Mercedes-Benz 300-Class

1 Answer

Brake Vibration


Your front rotor's were no cut right, there wrap so when you brake you feel that out of roundes, take your car back and have them cut the rotor's right, make sure they mic the rotor's to get a mim thickness or rotor will wrap again, if tis thin rotor's will have to be replace.

May 20, 2010 | 1998 Toyota 4Runner

2 Answers

Transmission swap


94,95 are the same 96-99 are the same. the 94-95 models have a 4 pin connector as the 96-99 have a round 12 pin connector. Hope this helps

Jan 30, 2009 | 1997 Dodge Ram 1500 Club Cab

2 Answers

Renault megane 1996 2.0L - Air con and wiper blades


My 1998 megane developed same prob dont worry its easy to solve! Open bonnet locate w/screen wiper motor lift up the black plastic moulding around windscreen wiper undo 10 ml bolt holding motor in place get a length of wire about 16ins pare off the end of wire wrap around the head of now loosened bolt tighten bolt replace cover then attach other end of wire to chassis or earth wire on battery hey presto everything functions again took me 10 mins and im a chef lol

Nov 08, 2008 | 2006 Renault Le Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...