Question about Cars & Trucks

Open Question

OWNER MANUEL how do i set or reset alarm on 06 ENVOY

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need help bought house with this system asking for access code and we don't have it says system is armed need to disarm please help reset it

Contact the previous owner or the sales team that sold the property! This will be an owner set alarm....... We would not be able to help without knowing the make and model of alarm anyway!

Nov 02, 2016 | Cars & Trucks

1 Answer

Gmc envoy what are main problem with the vehicle.

their are many problems with any vehicle and envoy/trailblazer[top seller ] have troubles some of the complaints were in the early 02 -03 the sun gear in transmission would crack some were the rear light panel corrosion problem a recall for some 06-07 in the northeastern area for drivers door circuit shorts due to cold weather road salts being able to seep past window and a few not many of the 02 trailblazers /envoys for an air bag module inspection last year recall for some 06-09 for a drivers headlight module the 05 had some for windshield sealant not fully cured their has not really been major problems with them but like with any vehicle the owner will either love them or hate them

Jul 27, 2015 | GMC Cars & Trucks

1 Answer

Red alarm light stays on all the time. How do I get rid of this problem. Car starts no problem.


reset the car alarm with the default reset button

this should return it back to its default setting and turn the light off

if its a factory fitted alarm consult manufacturers manuel


May 28, 2015 | Cars & Trucks

1 Answer

Car alarm goes off when I use the key to open doors or start engine on my 2006 GMC Envoy. Problem started when I installed new battery.

Not familiar with the envoy, but most all GMC trucks have a alarm reset button under the dash by the steering column to reset after battery problems. Why did you change the battery? It may also be your starter has shorted out which will set off the alarm. Good Luck

Nov 23, 2013 | 2006 GMC Envoy

1 Answer

Reset alarm

The factory alarm is reset every time the key is turned on in the ignition and the key or remote are used to unlock the door.

Feb 24, 2012 | 2003 GMC Envoy

1 Answer

What does the code p0483 means for a gmc envoy?

DTC P0483 is set when the difference between the commanded cooling fan speed and actual cooling fan speed is greater than 1,000 RPM.
Reset the comp with the scanner, if it comes up again, then you may need to replace your fan clutch.
Technical Service Bulletin (TSB #04-06-04-090A) says, "The diagnostic calibration in the PCM may allow the DTC P0483 to set improperly." The bulletin directs technicians as follows: "Reprogram the Powertrain Control Module (PCM) with a new service calibration titled, 'New calibration to reduce the potential for setting P0483.'" this will have to be done at the dealership, or by a qualified mechanic.
Good luck.

Aug 19, 2011 | 2004 GMC Envoy

1 Answer

I am having problems with my 2006 Envoy. The ac is working but not blowing air out of vents. It completely stopped working for about two days then started back. Now it has quit again.

try replacing the fuse for the a/c it might be near its death and is having bad connections. use your owner manuel to locate the correct fuse or even the fuse box has a guide inside the box

May 02, 2011 | 2006 GMC Envoy

1 Answer

I had disconneted the negative post on my battery. After reconecting and atempting to start the vehicle, the anti theft light started flashing as well as a blue light on the sterring column. the car will...

In some cases, it's possible to re-set the anti-theft by physically unlocking your car door with the key.
The interruption of power is a safeguard measure to ensure the car has been entered by the owner and not somehow bypassed. Using your key should reset the alarm and allow you to start the car.

Mar 16, 2011 | Ford Mustang Cars & Trucks

1 Answer

Service airbag light on in my 06 envoy

check the wiring at the column make sure nothing is dis connected you might have hooked up a wire in wrong place voltage change will cause light to come on

Oct 19, 2009 | 2002 GMC Envoy

2 Answers

Need to shut auto light mode off for my headlights

In your owners manuel, under driver configurable controls it will tell you how to turn them off. If you can't find it I can look it up at work tomorrow. Please let me know. Good Luck

May 19, 2009 | 2006 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14264 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides