Question about Cars & Trucks

1 Answer

Alternator 92 Lumina Z34, its on the bottom placement of a alternator, what do I do after taking the tie rod end off and I have the shield off as well? L.Cain

V6 204 3.4L DOHC Continue = What comes off now? and the last thing is to take the exhaust off to get at it to remove and a 4 foot extension from the right side to loosen the back alternator bracket? L. Cain

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Cars & Trucks Expert
  • 249 Answers

I have remoced some difficult alternators in my time but never have i had to remove all this.
I think you may find it easier to remove an engine mounting and lift tne engine a little ??

Posted on Apr 24, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Alternator removal


it does come out the bottom, remove the tire, and inner fender splash shield, and it will come out through there.

Mar 03, 2015 | 2003 Chrysler PT Cruiser

1 Answer

How do you change a altenator on a 94 chevy lumnia z34


Alternator is located on the passenger side under the engine. It is hard to get at because it is between the engine and the passenger axle. Disconnect the battery then the wires to the back of the alternator. Remove the serpentine belt then remove the bolts that hold the alternator to the engine.

Jan 05, 2013 | 1994 Chevrolet Lumina

1 Answer

How do you change a 2000 ford contour tire


Instructions

1 Park the car on a level surface. Turn the engine off. Open the hood and disconnect the negative terminal from the battery cable.

2 Loosen the lug nuts on the driver's side tire. Jack the car up till the tire has left the ground, and you can get a jack stand underneath to support the For Contour's weight. Lower the car onto the jack stand and remove the jack. Remove the tire.

3 With a socket wrench, remove the four bolts in the wheel well that hold the mud flap and the flap that protects the radiator from road debris.

4 Loosen the belt tensioner bolt by reaching in from the top of the engine with a socket or box wrench. This bolt is usually found in the engine block, holding a spacer bar to the alternator; consult your manual for the location in your specific year of Ford Contour, as they vary. Remove the belt from the pulley.

5 Pull the cotter pin from the ball joint stud where it connects to the wheel knuckle in the wheel well. Using a box wrench, loosen, but do not remove the nut on the stud.

6 Attach the Tie Rod End Puller to the tie rod by placing the tie rod end in the channel on the top of the steel grip of the puller, and twist the screw clockwise until the tie rod comes free. Separate the tie rod from the wheel knuckle.

7 Remove the nut on the ball joint stud that you loosened in Step
5.

8 Draw, mark or photograph the way that the wires connect to the alternator and then disconnect the wires.

9 Loosen and remove the three bolts holding the alternator in place. There will be one at the top, one at the bottom and one in the rear holding the alternator in a bracket attached to the car frame. Withdraw the alternator through the wheel well.

10 Installation is the reverse of removal. Remember to use a new cotter pin at the nut on the ball joint stud.

Thanks

Apr 01, 2012 | 2000 Ford Contour

2 Answers

Procedure to replace alternator 2006 mercury mariner 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the lower splash shield bolts and the pin-type retainers.
    NOTE The LH lower splash shield must be removed before the RH lower splash shield.
  3. Remove the lower splash shields.
  4. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside
  5. Disconnect the alternator electrical connector.
  6. Position the alternator B+ protective cover aside and remove the alternator B+ terminal nut.
  7. Remove the A/C compressor bolts. Use a tie-strap and position A/C compressor aside.
  8. Loosen the alternator nuts.
  9. Remove the lower alternator studs.
  10. Remove the upper alternator bolt and the alternator.

0996b43f80200f35.gif

Feb 18, 2011 | 2006 Mercury Mariner

2 Answers

Firing order on coil packs 92 lumina z34 5 spd


For the 1992 & 1993 Chevrolet Lumina 3.4L DOHC V6

Firing Order:
1-2-3-4-5-6

Cylinders:
.......(back)......
F|...1....3....5...|
A|...................|
N|...2....4....6...|
.......(front)

Ignition Coil Connections:
...............(back)
....1...4........3...6.......2...5...
.|..o...o..|..|..o...o..|..|..o...o..|
.|....O....|..|....O....|..|....O....|
...............(front)

May 03, 2010 | 1993 Chevrolet Lumina

2 Answers

How can I remove an altenator from a 98 ford contour se 2.5 l motor. And what are any suggestions?


Fig. Fig. 5: Alternator mounting-2.5L engine
  1. Disconnect the negative battery cable.
  2. Release the drive belt tensioner and remove the drive belt from around the alternator.
  3. Raise and support the vehicle.
  4. Remove the passenger side front wheel and fender well splash guard.
  5. Disconnect the passenger side outer tie rod end from the spindle. See .
  6. Remove the exhaust system Y-pipe.
  7. Unplug the connectors and remove the cables from the alternator.
  8. Remove the alternator brace retaining bolts and the brace from the vehicle.
  9. Remove the passenger side halfshaft. See .
  10. Remove the alternator mounting bolts and remove the alternator from the passenger side fenderwell.

To install:
  1. Install the alternator on the bracket and tighten the mounting bolts to 29-40 ft. lbs. (40-55 Nm).
  2. Install the passenger side halfshaft. See .
  3. Install the alternator brace and tighten the retaining bolts to 15-22 ft. lbs. (20-30 Nm).
  4. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
  5. Install the exhaust system Y-pipe.
  6. Install the passenger side outer tie rod end to the spindle.See .
  7. Install the passenger side fender well splash guard and front wheel.
  8. Lower the vehicle.
  9. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
  10. Connect the negative battery cable.

Mar 15, 2010 | 1998 Ford Contour

2 Answers

How do you get the one bolt off to take the alternator off and replace it


Give this to your brother in law:

Park the car on a level surface. Turn the engine off. Open the hood and disconnect the negative terminal from the battery cable.
  • Step 2 Loosen the lug nuts on the driver's side tire. Jack the car up till the tire has left the ground, and you can get a jack stand underneath to support the For Contour's weight. Lower the car onto the jack stand and remove the jack. Remove the tire.
  • Step 3 With a socket wrench, remove the four bolts in the wheel well that hold the mud flap and the flap that protects the radiator from road debris.
  • Step 4 Loosen the belt tensioner bolt by reaching in from the top of the engine with a socket or box wrench. This bolt is usually found in the engine block, holding a spacer bar to the alternator; consult your manual for the location in your specific year of Ford Contour, as they vary. Remove the belt from the pulley.
  • Step 5 Pull the cotter pin from the ball joint stud where it connects to the wheel knuckle in the wheel well. Using a box wrench, loosen, but do not remove the nut on the stud.
  • Step 6 Attach the Tie Rod End Puller to the tie rod by placing the tie rod end in the channel on the top of the steel grip of the puller, and twist the screw clockwise until the tie rod comes free. Separate the tie rod from the wheel knuckle.
  • Step 7 Remove the nut on the ball joint stud that you loosened in Step 5.
  • Step 8 Draw, mark or photograph the way that the wires connect to the alternator and then disconnect the wires.
  • Step 9 Loosen and remove the three bolts holding the alternator in place. There will be one at the top, one at the bottom and one in the rear holding the alternator in a bracket attached to the car frame. Withdraw the alternator through the wheel well.
  • Step 10 Installation is the reverse of removal. Remember to use a new cotter pin at the nut on the ball joint stud.
  • Nov 25, 2009 | 1997 Ford Contour

    2 Answers

    Can't get alternator out. How do i get it out


    Raise car on lift,Remove right front wheel,Remove right outer tie rod end cotter pin and nut.Separate tie rod end from spindle,That's where you will be bringing the alternator out,

    Nov 17, 2009 | 1996 Ford Contour

    1 Answer

    Interchangeable parts between vehicles?


    Battery and alternator sometimes the radiator depends on mounts, some of the sensors

    Oct 26, 2009 | 1992 Chevrolet Lumina

    1 Answer

    Does anyone knows how to remove the alternator i


    1. Disconnect the battery ground cable, then disengage the alternator drive belt from the alternator pulley.
    2. Raise and support the vehicle, then remove the righthand wheel and tire.
    3. Remove the righthand outer tie rod end from righthand spindle.
    4. Remove exhaust system Y pipe as follows:
      1. Remove the front and rear Y pipe flange fasteners from the exhaust manifolds.
      2. Remove the stud bolt and nut retainer from the oil pan, then remove the two remaining nuts and bolts from U pipe outlet connection.
      3. Discard the exhaust converter inlet gasket, then remove the Y pipe.
    1. Disconnect wire harness attachments to integral alternator/voltage regulator, then remove the alternator brace bolts from the alternator.
    2. Remove the righthand halfshaft.
    3. Remove the alternator bolts from bracket, then rotate the alternator and remove it through the righthand side of the vehicle.
    4. Remove the bracket bolts and bracket from the cylinder block.
    5. Reverse the procedure to install, noting the following:
      1. Torque the alternator bracket bolts to 15-22 ft lb.
      2. Torque the alternator bolts to 29-40 ft lb.
      3. Torque the alternator brace bolts to 15-22 ft lb.
      4. Torque the output terminal nut to 6.7-8.1 ft lb.

    Sep 17, 2009 | 1996 Ford Contour

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...