Question about Cars & Trucks

Open Question

The coiled wire is out of its mount cant see how to reinstall

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition coil on 1991 GMC Suburban


check out AA1car.com It helped me out a lot and it's free.. An awesome site if you are willing to search a bit. The coil is on top of the distributor cap. remove the top cover then the 4 small bolts holding it on. Unplug it fro the side, 3 wires... then just replace. Make sure to reinstall the ground wire that is located under one corner of the coil and held in place by the mounting bolt.

Nov 08, 2013 | 1991 GMC Suburban

1 Answer

Where is the ignition module on a 99 plymouth voyager


Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Cars & Trucks

1 Answer

Where is the ignition module in a 99 voyager


Hi Eric:
Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Plymouth Cars & Trucks

2 Answers

How do I replace the ignition coil in my 2002 ford taurus



Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.

Dec 19, 2010 | 2002 Ford Taurus

1 Answer

90 yj only 70k on it sat for 2 years. 4.2 carb, ran one day now hard start, runs for 15 min. then dies. cant restart unless kept in start position. not ign. switch, fuel pump, cap, rotor, wires, plugs, or...


Check the fuel for a presence of water. I'm sure there was a recall notice on the gasket on top of the fuel tank where the sending unit mounts. My YJ sat for a year and had water in the tank from this leaking. Drain and drop the tank, replace the gasket, and reinstall.

Oct 09, 2010 | 1990 Jeep Wrangler

1 Answer

I cant get to the coil pack? whats the easiest way?


LABEL AND NUMBER EACH SPARK PLUG WIRE IN ORDER.USING MASKING TAPE OR ANY KIND OF TAPE THAT YOU CAN WRITE ON USING SHARPIE MARKIE.WHEN ALL PLUGS WIRES BEEN LABEL REMOVE THEM LAY THEM ASIDE.DONT REMOVE WIRES FROM SPARK PLUG END JUST THE COIL.REMOVE IGNITION COILS AND MODULE ASSEMBLY MOUNTING NUTS, THEN REMOVE THE ELECTRICAL CONNECTORS THEN REMOVE THE COILS AND MODULE ASSEMBLY.WHEN DONE PUT EVERY THING BACK IN VISA VERSA.

Sep 17, 2010 | 1995 Chevrolet Cavalier

1 Answer

How to remove a 1989 pickup chevrolet ignition coil ,6 cil.,chayane


GM Full-Size Trucks 1988-1998 Repair Information
Ignition Coil - REMOVAL & INSTALLATION
(sSee Figures 1, 2 and 3)

8182f5f.jpg

Fig. 1: Ignition coil mounting-4.3L engines
  1. Tag and unplug the wiring connectors from the coil and the coil wire.
  2. Unfasten the retainers securing the coil bracket and coil to the manifold.
  3. Remove the coil and bracket and drill out the two rivets securing the coil to the bracket.
  4. Remove the coil from the bracket.
To install:
The replacement coil kit may come with the two screws to attach the coil to the bracket. If not, you must supply your own screws.

df834a8.jpg

Fig. 2: Ignition coil mounting-5.0 and 5.7L engines

8dc14f4.jpg

Fig. 3: Ignition coil mounting-7.4L engines
  1. Fasten the coil to the bracket using two screws.
  2. Fasten the coil and bracket to the manifold. Tighten the retainers until they are snug.
  3. Engage the coil wire and the wiring connectors to the coil.

Hope this help to solve it (remember comment and rated this).

Apr 21, 2010 | 1989 Chevrolet C2500

3 Answers

Ignition module where do I find it.


The ignition coils are mounted on it. Just follow the spark plug wires.

Nov 18, 2009 | 2005 Chevrolet Impala

1 Answer

Ignition Coil A,B,C Primary/Secondary malfunction


Remove the Caravan Ignition Coil Step1 Look under the hood for a distributor. The spark plug wiresmag-glass_10x10.gif connect into the distributor cap. If you don't see a distributor, you may have a model with a distributorless ignition system. Step2 Find the ignition coil. On a Dodge Caravan, the ignition coil is at the back of the intake manifold. Disconnect the negative battery cable to prevent injury while you work. Step3 Determine whether you need to remove the windshield wiper/motor module assembly. This won't be necessary on all models. Step4 Disengage the connector securing the wiring harness connector to the Dodge Caravan ignition coil. Then, disconnect the ignition wire from the ignition coil. Step5 Use a socket set to remove the mounting bolts. There are upper and lower mounting bolts. Separate the ignition coil from the mounting bracket. Install the New Ignition Coil Step1 Insert the new ignition coil. Mount the Dodge Caravan ignition coil to the mounting bracket. Step2 Attach the mounted assembly to the intake manifold. With a Torque wrench, tighten the fasteners securing the ignition coil to the mounting bracket with 96 inch pounds of torque (10 Nm). Step3 Tighten the bolts that secure the intake manifold to the bracket with 115 inch pounds of torque (13 Nm). Step4 Connect the wire harness and any other parts you removed, including the negative battery cable.

Feb 23, 2009 | 1998 Dodge Grand Caravan

1 Answer

Bad miss


REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0900c1528008ee09.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Ignition coil mounting-4.3L engines
  1. Tag and unplug the wiring connectors from the coil and the coil wire.
  2. Unfasten the retainers securing the coil bracket and coil to the manifold.
  3. Remove the coil and bracket and drill out the two rivets securing the coil to the bracket.
  4. Remove the coil from the bracket.

To install:
The replacement coil kit may come with the two screws to attach the coil to the bracket. If not, you must supply your own screws.


0900c1528008ee0a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Ignition coil mounting-5.0 and 5.7L engines


0900c1528008ee0b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Ignition coil mounting-7.4L engines
  1. Fasten the coil to the bracket using two screws.
  2. Fasten the coil and bracket to the manifold. Tighten the retainers until they are snug.
  3. Engage the coil wire and the wiring connectors to the coil.

  4. Hope this helps
    Lefty64

Dec 23, 2008 | 1988 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...