Question about Ford Ranger

Open Question

Seatbelt light stays on even after you have put on seatbelt in a 2001 Ford Ranger. Why?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76630 Answers

SOURCE: Ford Focus seatbelt locked

There is a gas cylinder that tightens the belt in a minor collision, it is a one time use part it is independent of the air bag deployment system, you will have to replace the seat belt gas cylinder, that may mean a new belt assembly, not sure on focus.

Posted on Aug 22, 2008

Ad
tripletauto
  • 1450 Answers

SOURCE: the SRS light stay on

SRS stands for supplemental restraint system. You have a problem with the airbag system. The seat belts have sensors to let air bag module know if they are buckled. Could be a bad buckle seat belt will work fine .This may be a common problem is why they said seatbelt problem

Posted on Sep 05, 2008

pittmanc
  • 194 Answers

SOURCE: Airbag/seatbelt dash light flashing a code.

the sencors are very bad for going out you could have hit a good bump and now it doens't know what to do but you shoul not have a problem with it like it is if you diside to leave it alone

Posted on Dec 05, 2008

  • 298 Answers

SOURCE: seatbelt light on

There is a tiny switch under the **** area of the seat that tells the car someone is sitting there... and a tiny switch in the seatbelt CLICK mechanism. These only have 2 wires which go down to the floor, alongside the running board and up to the dash. The switch nder your **** is NormallyOPEN and CLOSES (makes contact) when someone weighing 50lb or more sits in the seat (smart huh) It could be bent, broken, come loose from its moorings or have a wire loose... At the same time, the passenger seat also has shcu a switch and it might be STUCK or shorted. Same for the seatbelt CLICK mechanisms on both sides. If you don't like loosening seat bolts, pulling up carpeting and removing the inside panels, etc. what we call 'troubleshooting'. find someone that does - or take it to a dealer.

Posted on Jan 15, 2009

  • 102 Answers

SOURCE: 2002 VW Beetle GL seatbelt warning light stays on all the time

most likely if you look under the 2 front seats and inspect the wires that come from the belt you'll find a broken wire. just repair broken wire and you'll be back in business.

Posted on Mar 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers side seatbelt is fully locked and will not engage so it can be extended and utilized. Is there any simple fix


not really there is a check ball in these, that work with the movement of the car (easiest way to say it) so when you start to come to.a stop, this check ball moves and locks the seatbelt , if your car was in.a.accident then.have it replaced, but if not and you are pulling on it and it is staying locked, then the safest thing to do is replace the seatbelt

Dec 05, 2013 | 2004 Ford Ranger

1 Answer

2006 grand cherokee seat belt


Have the same problem in my 98 Toyota Rav4. I squirted the female buckle (bolted to seat, not holding strap harness) with wannabe WD-40 lubricant from the $1 store, and it seem to have solved the problem. I'm guessing the spring mechanism is worn out, which is why the harness buckle won't lock. Another solution is to replace the female lock buckle with an identical part from the used parts junkyard store.

The seatbelt light on the dash stays "on," even when everyone has their belt on, but I don't bother servicing that. If yours have an audible alarm instead of an indicator light on the dash, locate the source of the alarm sound and disconnect the wires to silence the sound.

Nov 29, 2013 | Cars & Trucks

1 Answer

96ChryslerCirrus: 'door' warning vs odometer miles, Dome light stays on.


In the Ford Ranger, the light switch can be found in the door, right by the latch. You may need to use some WD-40 to get to work properly. -------------------------------------------------------------------------------------
zed bull

Nov 28, 2012 | 1996 Chrysler Cirrus

2 Answers

Is there a passcode or sequence to disable the


As far as I know that seat belt warning chime and light is there for your safety and protection, it should not be bypassed in any way.
There is no by pass seqwuence or code to eliminate this safety device.
Buckle up, its the law.

May 09, 2010 | 2002 Ford Mustang

1 Answer

I have a 1998 ford ranger and the door adjar wont turn off and the dome light stays on after i exit the truck.


make sure the seatbelt isn't getting caught in the door jam when you close the door, it could be enough to keep the door slightly ajar or.............. when you slam the door it's possible that another door/hatch could be popping open slighlty if the latch on that door is not 100% holding tight so check each one....good luck

Feb 13, 2010 | 1998 Ford Ranger SuperCab

1 Answer

2007 FORD RANGER TROUBLE CODES #B2292, B2293


These 3 codes have to do with restraint system.
B2292 Seatbelt pretensioner fault.
B2293 Passenger front airbag fault.
B2691 Seatbelt buckle switch circuit fault Ft.driver side.

Sep 18, 2009 | 2007 Ford Ranger FX4 Off-Road

1 Answer

The seatbelt light and bell stay on even if you buckle the seatbelt. is their a way to bypass or jumper out this on a 2000 ford mustang?


seems like the connection is disconnected on the buttom of the seat that goes to the seatbelt click,make sure its connected.if that is connected then change the thing that the seatbelt goes in on the seat that clicks in cause could be jamed common problem and wont let the light or noise go of .if my info was of any help to you please leave a comment ,thankyou.

Sep 02, 2009 | 2000 Ford Mustang

1 Answer

Drivers side seatbelt connected When truck is


sensor in the seat belt bukle needs to be replaced

Aug 01, 2009 | 2004 Ford F150

1 Answer

The Fasten Seatbelt Light on my 2002 Mustang will not shut off


you need to be sitting in the drivers seat, not the passenger.

Mar 17, 2009 | 2002 Ford Mustang

1 Answer

Seatbelt Unlatches


This sounds like something broken in the latch. Do yourself a favor. Before it comes unlatched in an accident, go to your local dealer and get a replacement latch ASAP. That is one device in a car you shouldn't ever have to question. If it doesn't work right, replace it.

Feb 03, 2009 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...