Question about 2005 Jeep Liberty

Open Question

Removed wiper arm off the wiper motor shaft jeep 05 liberty, panel off door bolt off, but can't remover the motor. How do you remove the outer looks like rubber cup to seal the shaft from water entry

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 54 Answers

SOURCE: remove front wiper arms. Lift arm, slide out

Just pry them off. Make sure the tab is out the whole way. Sometimes they can be tough to get off. Spray with wd40 it should aid in getting it loose. You could even tap it a few times with a rubber mallet or a light hammer, just be careful. Good luck if this helps let me know.

Posted on Jun 19, 2009

  • 67 Answers

SOURCE: removing the wiper arms on a 1994 jeep cherokee sport

Pry up on the locking lever with small screwdriver, then pull the wiper arm off the pivot

Posted on Mar 30, 2010

  • 6982 Answers

SOURCE: how to remove 1996 Jeep Cherokee wiper arm

At the base of the arm where it attaches to the drive stub, you should see a "L" tab made of stainless steel. that tab swings out, disengaging the arm. you then need to pull and wiggle the arm a bit to get it free from the stub. When you put it back on, make sure you swing the tab back in or the arm will fall off later.

Posted on May 14, 2010

  • 4 Answers

SOURCE: 2006 Jeep liberty sport remove door panel driver side

The window regulator mechanism on these vehicles is faulty and failure is repetitive. There is a new model regulator which can be put in, but I understand that requires a new window also. A very good option is the regulator repair kit from Steiger which repairs the existing regulator and replaces the failure prone plastic part with a metal replacement. I have not seen one of these fail. The site for the kit is:
http://www.steigerperformance.com/products/sp13001.html

The kit is specific to the window so a front right works only on that door and no other, so be sure to order the correct kit for what you need. It comes with a good set of instructions; and you can, if you are a bit handy, do it yourself. You can download the instructions first before buying to give them a look. I would recommend this over ever using an original equipment part. I have now replaced every one on my liberty.

Posted on Jan 11, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis


1992-98 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle


ffed3a6.jpg



Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Aug 02, 2010 | 1992 Mercury Grand Marquis

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Oct 01, 2009 | Ford Taurus Cars & Trucks

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Cant take off the windsheild wipers


Here is the procedure to remove the wiper motor. It says to remove wipers by removing the nut covers then remove the wiper nuts. Is this what your talking about?
If your talking about the wiper arms they just pop off at the swivel.
Use this link for info on removing blade assy.
http://www.autozone.com/az/cds/en_us/0900823d/80/04/f8/26/0900823d8004f826/repairInfoPages.htm

Wiper Motor
Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the wiper pivot arm nut covers.
  5. Remove the nuts and the wiper pivot arms.
  6. Remove the cowl top vent panels.
  7. Remove the four bolts, wiper mounting arm and wiper pivot shaft assembly.
  8. Disconnect the electrical connector.
  9. Remove the bolt and the windshield wiper motor operating arm from the motor.
  10. Remove the three bolts and remove the windshield wiper motor.
  11. To install, reverse the removal procedure.

Jan 28, 2009 | 2005 Ford Taurus

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...