Question about Ford Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
there is a new tsb to reprogram the system take to your local ford dealer to get a warranty reprogram on your myford touch system
Posted on Dec 09, 2010
First off, if you're attempting this, I'm assuming you're someone mechanically inclined or at least somewhat of a grease monkey -
NO NEED for me to tell you how to change the first THREE spark plugs that stare at you when you pop-up your hood - These should be child play for you... if not, take your car to a shop and stop reading... (no offense)...
The back ones are the fun ones to get to!
Keep in mind you will need to move a lot of the wire harnesses around - you may have to cut a few tie-down clips or zip-ties to help you out.
1 - Remove the Air Box - Remove Air Filter - No need to dismantle the whole Unit into pieces... Loosen up the clip clamp at the Throttle Body and pull out the whole Unit -
** Disconnect the Sensors, Disconnect the Front Rubber Hose and the little valve underneath **
2 - Loosen and remove the screws that hold down the manifold (6 total I think in the front) - There is a super long one all by itself in the middle - the others are at the edges
** Also, take your time to detach the Wire Harness/Hoses strapped to the Manifold (in the front) you can do this by removing the black electrical tape and replacing later when you're done ...
3 - There is one screw under the Throttle Body - remove it - it's kinda' hidden but you'll see it.
4 - There is another one on top of the manifold towards the back - it's hidden under the hood cowl
** Look on top of your engine towards the back - Locate two rubber hoses attached to the manifold - FYI - You will be working in a very TIGHT spot, but be patient and make sure you don't give up! **
5 - Loosen/Detach Rubber Hose on the Left (Pass Side) attached to the Manifold (PCV Valve?) - Make sure you don't drop it - it connects the manifold to the Engine - it's a small "L-shaped" hose
** There is a tiny connector right below that valve, you cannot see it but you can feel it, it's easy to remove, just unplug it - AGAIN, it's a tight spot, but not impossible to work with. **
6 - Loosen/Detach another Rubber Hose on the Right (Driver Side) and your manifold is ready to come off - Move it around, and pull it out... careful with the wire harnesses around and the other hoses that are sitting on top of the engine.
Make sure you Disconnect the Mass Air Flow Sensor and Air Temperature Sensors!!!
Once you pull out the Manifold - it is easy as cakes to replace your three other Spark Plugs -
Follow the steps backwards and VOILA! - It is a LOT easier to do then all this jargon I've written
Posted on Jan 30, 2011
You mean cylinder location
on a v6 front to back
1&4 are at the motors front end
All you had to do was type:Ford Edge Cylinder Order
or whatever you want
Posted on Dec 03, 2014
Sounds like the steering wheel is locked or there is a problem with the ignition switch
Posted on Dec 06, 2014
Testimonial: "No steer lock, no problem ignition either."
Tips for a great answer:
Nov 08, 2015 | 2009 Ford Fusion
Dec 03, 2014 | 2010 Ford Edge
Feb 02, 2013 | 2008 Ford Edge SEL
Jan 21, 2013 | 2011 Ford Edge
Feb 01, 2011 | 2007 Ford Edge SEL Plus
Mar 06, 2010 | 2007 Ford Edge SEL Plus
Nov 18, 2009 | 2007 Ford Edge SEL Plus
Jun 16, 2009 | 2007 Ford Edge SEL Plus
Nov 20, 2017 | Ford Escape Cars & Trucks
58 people viewed this question
Usually answered in minutes!