Question about Cars & Trucks

Open Question

Engine starts but runs rough and suts down after about five to ten seconds.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: chrysler 3.3 vin r v6 mini van, starts then dies

Charlie. You have replaced the ECM on your van?.
Kedwin,, Your problem is, the computer on that 3.3 L.
Need to be programed with the VIN nember of your car.
The Antitheft System will disable the injectors due a incorrect VIN, Bucause the body computer is not recieve the correct pasword between 5 seconds after start up.
YOU have 2 options. 1 get a ALOHA Smith. some of they have the computer required to program ECMs.

The other option is: Get a new ECM from the dealer, They will program if ask for that.

NOTE:::::: Other way is . Put the body control module with the computer from the same car.

OK... I hope this work for yours.
If NOT letme know I can look for more information.
Thank you.

Posted on Jul 17, 2008

  • 119 Answers

SOURCE: fuel system

Check the fuel system, chenge fuel filter. clean the fuel tank.

Posted on Oct 19, 2008

  • 141 Answers

SOURCE: Engine runs rough after about ten minutes /idles really low

Just trowing some suggestions out there, but, I would check the idle air control valve (solenoid) or the throttle position sensor. If they check out then my last guess would be the map sensor or the vaccuum to the map sensor. Hope I was able to help. Best wishes.

Posted on Jan 17, 2009

  • 16 Answers

SOURCE: 91 honda civic dx 1.5L quit running properly.

bro, check ur main relay. its under the dash. replace it, check also ur distributor(replace it). and also your ECU

Posted on Feb 22, 2009

Testimonial: "right answer but I received it much too late. I went to a mechanic and paid him to fix it."

  • 10 Answers

SOURCE: 1993 Eagle Talon Tsi starts rough then dies off, bad timing?

First thing you can do to try a simple fix is replace each spark plug, check each plug for signs of fuel/air mixture

if your plug is black is rich, if ur plug is white is lean.

in this case repost your findings. in the mean time if they look golden or light brown, replace them and make sure they are gapped to ur level of psi you are running.

you can find the gap specs for how much boost you are running on most DSM websites or by searching.

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Check & Reset Your 2002-2006 Nissan Altima Service Engine Soon (SES)...


The following directions will help you decode your 2002-2006 Nissan Altima's Service Engine Soon (SES) light and reset it.<br /> <br /> <span style="font-weight: bold;">Obtain The Trouble Code</span><br /> <ol> <li>Turn the ignition key to the ON position and wait three seconds.</li> <li>Put the accelerator pedal to the floor and release it five times in less than five seconds.</li> <li>Wait exactly seven seconds. Put the accelerator pedal to the floor for ten seconds until the SES light flashes.</li> <li>Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code.<br /></li></ol> <ul> <li>Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) </li> <li> The next three digits blink faster (0.3 second) and have a 1 second pause between digits.</li> <li>The ECM code repeats until you turn the ignition key to the OFF position.</li> <li>You can look up the trouble codes in the Service Manual.</li> <li>If you get four blinks of ten, or 0000, the ECM indicates no malfunction.<br /></li></ul> <br style="font-weight: bold;" /><span style="font-weight: bold;">Clear The Trouble Code</span><br /> <ol> <li> Clear the code and the SES light by holding the accelerator pedal down to the floor for 10 seconds or more while the SES light is blinking.</li> <li>When the pedal is released, the ECM will erase the trouble code(s).</li></ol>

on Feb 15, 2011 | 2002 Nissan Altima

1 Answer

Where is the fuel reset button for a 2004 Chevrolet Silverado 2500 HD 6.0 L fuel injection?


For vehicle with steering wheel conrtols ,to reset the fuel,Press and hold the select button for five seconds while the fuel filter life message is displayed . The message will appear on the DIC for ten second
For vehicle without steering wheel control ,do the following, without pressing the pedals,turn the ignition key to the on position without starting the engine ,wait five seconds,completely press the the brake and the accelerator pedal simutaneously, and hold for ten seconds ,the system is now reset ,
The next time the engine is started the message will no longer be displayed, Always reset after a fuel filter change

Mar 03, 2012 | 2004 Chevrolet Silverado 2500HD

1 Answer

2002 vue v6...starts and runs well however when I stop , shut off the engine, then try to start after half hour , it wont start


Lookfor a light on the dash that says SECURITY or ANTITHEFT. If you see this light, that is a sign of a failed or failing antitheft system, which will disable your vehicle. This link explains

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Nov 06, 2011 | 2002 Saturn VUE

1 Answer

1997 dodge caravan stalls after driving changed egr valve an still same problemhad autozone check for codes but none came up.runs ok but after temperature warms up starts running rough an dies.after it...


My van cuts off after driving on a long stretch of highway. Around town it does pretty good. It starts back up after ten or fifteen mins. I changed the oil, oil filter, coil pack new spark plugs, and fuel fliter. It still does it. Does any one know what this could be???? O its a 2001 dodge caravan

Oct 30, 2011 | 1997 Dodge Caravan

1 Answer

Wife used cig lighter adapter last night to blow up air mattress this morning new battery less than 1 month old wont start car. charged battery now when i turn the ignition key to start car the car alarm...


turn the igntion on, don't start, let it set for ten minutes Turn it off for 5 seconds then try to start it. If it lost memory for some reason and doesn't start . then do this three times , after the third time start it. that is the relearn procedure. Have a charger on it for the 30 minute relearn. Relearn is on for ten m off five s on ten off five on ten off five then start

Jul 02, 2011 | Chevrolet Lumina Cars & Trucks

1 Answer

My son bought a 1997 Chevy Silverado, 6 cyl, and the engine light came on during the safety inspection. My mechanic said that the code was 401 which referred to the EGR. The truck has an electric ERG...


Did you install a new EGR Valve?

You said it has wires going to it &
you have a check light!! Got to think
these things through, if you don't have
the ablility to do any testing

Apr 21, 2011 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

2004 nissan quest DTC P0507. Can't get IAVL to


My quest 2004 idle below 500, start up then off, have to start couple times when the engine is cold. when i pushed the gas pedal, it smells gas.

Oct 21, 2009 | 2004 Nissan Quest

1 Answer

No spark


What about battery and alternator (serpentine belt).

Dec 05, 2008 | 1992 Mazda MX-3

1 Answer

Service engine soon


You have to time this perfectly or else it won't work.

Turn ignition switch on, after 3 seconds pump gas pedal five times. Once 15 seconds has passed hold pedal down for more than 10 seconds. The code will start to flash via the check engine light. Take your foot off the pedal. Watch it for a while, it will continue to flash the codes in a loop. To clear, hold the pedal down for more than ten seconds.

Oct 18, 2008 | 2004 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...