Question about Cars & Trucks

Open Question

Blanket blinking one side is blinking the other side is okay Is it no good now

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Honda Accord. Both turn signals on passenger side do not work. Both bulbs appear to be okay. Interior blinking arrow on dash board does not light up at all.


If the drivers side directional is working you probably have a burnt flasher unit located in the drivers side interior fuse box.

Mar 03, 2013 | 2003 Honda Accord

1 Answer

2008 CTS front directional not working?


Try replacing ALL directionals for the side that is not working properly. That fast blink in the back usually means bad bulb, but could also mean bad relay.

Can you elaborate? You say emergency flashers work, but FR directional does not. Does the bulb-in-question light when the E-flashers are going?

Oct 19, 2012 | 2008 Cadillac Cts

2 Answers

Have a 1988 Jeep Wagoneer with a few issues. My turn signals no longer blink or flash that I know of..?


Okay, the first thing to check is to turn on the signal on one side and see if the outside signal light comes on. if the light comes on then try replacing the flasher. Also see if your 4way flashers work or if they are also out. if they are out then check your fuse first.
If the fuses are good then try the flasher, if the flasher does not solve the problem then you may need to replace the turn signal switch. I have worked on a few of these and most of the time it was a flasher or the turn signal switch. good day.

Mar 02, 2012 | 1988 Jeep Cherokee

1 Answer

Left back turn signal not working after changing it. dashlight blics very fast


OOPS your disconnected. When it blink fast the side it blinks fast is where we need to hunt down the disconnection. S lets begin is if the front is turning fast then go to the rear if the rear is turning fast then we will go to the front. Now we are at the are were there is no trun lamp. Lamp is new okay, pull it out look in is it full of corrosion and this includes anti corrosion gell is there too much wpe it off. (the turn lamp on this are we are at is on right). put the buld back in did it fix it . No okay wiggle the wire did it come on if it did the we are going to need a whole bulb socket. by the way it would be better if the hazzard are on so this way we know that the flasher is working for the turn signal

Apr 22, 2011 | Dodge Caravan Cars & Trucks

2 Answers

They wont blink every thing else works turn signals wont blink when turn on


Most likely a bulb out. Try putting on a turn signal and get out to see if the lights are on. If there is one out it needs to be replaced. There is a possibility that it is the turn signal relay as well. This should be easily found using the owners manual for replacement.

Mar 03, 2011 | GMC Jimmy Cars & Trucks

1 Answer

The engine won`t start. Fuelpressure OK. Will start with startgas as long as gas sprays into air cleaner.


Sounds like injectors are not firing, check fuse of the injectors, check voltage of injectors if fuse is okay, voltage should be around 5V. If okay, you can check the ground side of injectors with a noid lite. If voltage is there, and no ground side, computer issue, or bad wiring. A good scanner can see if the injector voltage is okay.

May 25, 2010 | 1990 Mitsubishi Galant

1 Answer

When i press the emergency light button - only the light on right side start blinking. The light bulbs are okay as my indicators are working fine. Is there a fuse that has gone bad or some other issue?...


check the fusebox first to make sure a fuse hasnt blown,then try the relay for the indicators/hazard lights.if you havent got a circuit tester,this will be trial/error.

Feb 22, 2010 | 2000 Audi A4

1 Answer

1996 Dodge 3500 I Have No Turn Signals Or Hazard Lights If I Press The Brakes & Try The Signal It Comes On the Opposite Side But Want Blink


Check the 20 amp fuse if it's blown. This fuse is located in the power distribution box on the left hand side by the firewall. If the fuse is okay more than likely your multifunction switch needs to be replaced.

Jul 12, 2009 | 1996 Dodge Ram 3500 Club Cab

1 Answer

Dash bord Air bag blinks, car won pass inspection safety inspect


most times the problem is the rotating contact under the steering wheel has a break in the wiring of the flat ribbon connector, the part is called a clock-spring airbag contact.

Mar 17, 2009 | 1996 Nissan 200SX

2 Answers

Front blinker and run light don't work


Look at the second page of the diagram at the link. The flag "E" in lower right has power coming from the switch. It goes to the instrument cluster, right mirror turn indicator, and right front turn bulb. Is the instrument panel light blinking? How about the mirror? Use these facts to find the break in the wire. If none of these lights is blinking, the switch may be broken, as yadayada indicates. See page 1 at the link. It has a separate contact for the rear light, which is why the back can work and not the front, even though the switch is broken.
http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=123629

Nov 07, 2017 | 2006 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...