Question about 2003 Ford Windstar

Open Question

Were is crank shafts sencor on my 2003 ford wind star

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: ticking sound in dash board everything else seems

THIS NOISE IS COMING FROM A DEFECTIVE AIR TEMPERATURE CONTREOL BLEND DOOR ACTUATOR GEAR DRIVE SLIPPING TEETH.

Posted on Jun 23, 2009

Ad
  • 176 Answers

SOURCE: were are the crank shaft sencors located and how

Lower left of engine near oil filter (2).

Posted on Nov 05, 2009

  • 135 Answers

SOURCE: i have a 1998 ford

INSTALL PRESSURE GUAGE THEN CK, VOLTAGE TO PUMP PCM TURNS ON PUMP RELAY FOR 2 SECONDS WHEN KEY CYCLED ON ,, IF NO POWER CK INERTIA SWITCH ( MAY BE TRIPPED ) IF NO POWER TO INERTIA SWITCH CK FUEL PUMP RELAY IF NO VOLTAGE AT PUMP RELAY THEN CHECK FOR SPARK AT PLUGS IF NO SPARK CK PCM POWER RELAY IT SUPPLIES VOLTAGE TO PCM THAT INTURN POWERS FUEL PUMP RELAY

HOPE THIS HELPS

Posted on Aug 08, 2010

co7196
  • 3433 Answers

SOURCE: Were is the crank shaft position sencor located on

The crankshaft sensor shoul or is located at front of engine bolted to the block . It senses the crank position so it is mounted where it can ,in close proximity of the pulley. Ned

Posted on Apr 22, 2011

emissionwiz
  • 76109 Answers

SOURCE: I need help finding crank

The Crank position sensor is located on the drivers side front of the engine below the AC compressor and picks up its signal from the front crankshaft pulley trigger ring. In the picture below is a technican grasping the connection to the sensor and the sensor directly in front of the connector.





emissionwiz_161.jpg

Posted on Apr 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the O2 sensors on a 2003 ford wind star upstream


Have to look where exhaust pipe hooks-up to exhaust header pipe.
I looked at info for 3.8L engine.

26303990-d5pya0i0sr2gdavxtx1tpvby-4-0.jpg

Oct 07, 2016 | 2003 Ford Windstar

1 Answer

2003 ford focus check engine light kills motor


Start with a code reader several items will turn on check engine light and kill the engine Crank shaft sensor, cam shaft sensor, mass air flow meter, exhaust gas re circulation , manifold pressure sensor.

Jul 23, 2014 | 2003 Ford Focus

1 Answer

2001 ford taurus 3.0 ohv cam shaft sencor location


The single and double overhead cam engines take different sensors - it should be under a wiring harness close to the throttle cable.
Did you check the computer for trouble codes ?

Jul 13, 2012 | 2001 Ford Taurus

1 Answer

2003 ford F250 6.0 deisel..it will crank but will not start,cam and crank wil not synchronize..both are new. oil gauge wil not show pressure while cranking RPM.is around 48 rpms on a scan tool...


I HAVE A 7.3 DEISEL AND I DONT KNOW IF THE 6.0 HAS ONE OR NOT BUT MY CRANK SHAFT SENSOR WENT BAD AND THE TRUCK WOULD NOT START( JUST TURN OVER ) DEALER PUT NEW CRANK SHAFT SENSOR ON MINE AND FIXED THE PROBLEM...HOPE THIS HELPS...

Nov 29, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Were are the crank shaft sencors located and how


Lower left of engine near oil filter (2).

Nov 05, 2009 | 2003 Cadillac Deville

1 Answer

Ticking sound in dash board everything else seems to work in a 2003 ford wind star


THIS NOISE IS COMING FROM A DEFECTIVE AIR TEMPERATURE CONTREOL BLEND DOOR ACTUATOR GEAR DRIVE SLIPPING TEETH.

Jun 23, 2009 | 2003 Ford Windstar

2 Answers

Trouble starting


behind the main crankshaft pully you need to remove the crank bolt and use a puller to remove the pulley to get at it please rate -jeff

Sep 05, 2008 | 1994 Buick Roadmaster

Not finding what you are looking for?
2003 Ford Windstar Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...