Question about Ford Cars & Trucks

1 Answer

Settings of the tappets for ford Essex3.0l V6 motor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 3,828 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can you set tje valves in a 99 Ford f150

that 1999 ford F150 engine has self adjuster tappets

you could go back a few years and find the older F150 motor
with a set of old school manual adjuster tappets


Oct 28, 2016 | Ford Cars & Trucks

1 Answer

How do I set tappets on a 2004 2.5 tdi ford ranger it's the WL motor


Dec 10, 2014 | Ford Ranger Cars & Trucks

1 Answer

Does a 1999 frod contour have hydraulic lifters or mechanical lifters

Both the 2.0 liter 4-cylinder, and the 2.5 liter V6 are overhead cam engines. While all years of the V6 us hydraulic tappets, the 4-cylinder engines varied. From 1998 and earlier, they had hydraulic tappets. From 1999 on, they used shimmed mechanical tappets. Adjusting valve clearance on the later engines is a little involved, and, if you're not familiar with the procedure, it is perhaps best left to a professional mechanic who is familiar with the engine.

Aug 07, 2013 | 1999 Ford Contour

2 Answers

Tappet sequence for v6 essex motor

Is this a car? What year, make ,model and engine size is this.

Jun 24, 2012 | Cars & Trucks

1 Answer

I wish to check adjustment of tappet settings and would like to kn ow clearances i have hydraulic tappets. thank you 1966 windsor

Hydraulic tappets are normally zero lash ... not adjustable. That is why they are hydraulic ... the lifter takes up all the 'clearance' and is automatically adjustable.

Apr 05, 2011 | Ford Mustang Cars & Trucks

1 Answer

Has a ticking in the motor but its never been without oil.u hear the ticking on th right side of the motor

these vehicles do not have hydraulic tappets but shims and from the sound of it it could be a follower worn through or a noisey worn camshaft and the only way to find out is to take the top off and have a good look and measure the tappet settings ,inllet 12th and exhaust 15th

Feb 21, 2011 | 2000 Ford Focus

1 Answer

I have a cross flow 1300 gt with a weber carb that is us would a nikki carb do the job of the webber carb.

havent woorked on one of these in years ,used to build them on the assembly line in the 70s ,yes a nikki carb would do fine providing you get the right one ,these vehicles used a non progressive carb ,ie - the first venturi opened then the second one ,also all these engines from the first ones in 1971 have stelite coated valves and valve seats so you can use unleaded fuel of 98 octane in them.The tappet settings were done in the factory with a vacumn gauge and they do suffer from wear under the tappet face but the tappet is heat treated so dont reface them on a grinder ,replace them .tappet settings were if i remember for a gt were 12/14 inlet and 18/21 exhaust but i alway done them to 12 and 16 any tighter and it will drink petrol ,also the timing advance was different it advance a lot more compared to the normal engine,got me going now as i cannot remember the distributor code or the paint code on the thermostat housing on the head ,i do remember they had yellow build cards with GT in teh top right hand corner and heavier flywheels with bigger clutches .thanks for the memory jerker it makes a change from monster american cars on here and auto boxes ,Also built V6 zodiac engines as well as V4 transits

Jul 16, 2010 | 1983 Ford Escort Gt

2 Answers

I have a ford escape with a v6 3.0l engine. It

id say u have lifter problem not sure if u can adjust them some u can tho

Oct 23, 2009 | Ford Escape Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides