Question about Cars & Trucks

Open Question

Clutch removal and replacement - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get to Chevy s 10 1998 clutch pedal upper pin and bushing


CLUTCH PEDAL REPLACEMENT (CLUTCH) Document ID# 46043 Clutch Pedal Replacement

Removal Procedure



  1. Remove the master cylinder rod from the clutch pedal.


  2. Remove the clutch pedal from the support by depressing the side tabs.

Installation Procedure



  1. Position the clutch pedal into the support.


  2. Secure the master cylinder rod to the clutch pedal.

Good Luck

Aug 11, 2016 | Cars & Trucks

Tip

2004 Hyundai Tiburon Clutch.


First you need to remove the Transaxle.

Manual Transaxle System REMOVAL

1. Remove the engine cover.
2. Remove the battery terminal.
3. Remove the air duct.
4. Remove the battery tray.
5. Remove the air cleaner.
(1) Upper
(2) Lower
6. Remove the back-up lamp switch.
7. After removing the CKP sensor, O2 sensor and oil pressure switch wiring bracket, separate the connectors.
8. Remove the brake fluid leveling sensor connector.
9. Remove the speedometer driven gear connector.
10. Remove the clutch release cylinder mounting bolt.
11. Remove the cotter pin of the shift cable (transaxle side).
12. Remove the cotter pin of the select cable. (transaxle side)
13. Remove the clip of the shift cable (transaxle side).
14. Remove the clip of the select cable (transaxle side).
15. Separate the steering column shaft joint.
16. Separate the power steering oil pump hose.
Be careful not to leak after separating.
17. Separate the hose after removing the clip of the power steering return hose.
18. Remove the upper connecting transaxle bolt.
19. Separate the start motor.
20. Install the engine support fixture.
21. After removing the tire, remove the caliper.
22. Remove the transaxle side cover.
23. Remove the transaxle side under cover.
24. Separate the tie rod end.
25. Remove the wheel speed sensor and the knuckle mounting bolt.
26. Drain the oil.
27. Remove the transaxle mounting bracket.
(1) Insulator bolt
(2) Body side mounting bolt (Upper)
(3) Body side mounting bolt (Side)
(4) Transaxle side mounting bolt.
28. Remove the front roll stopper.
(1) Insulator bolt
(2) Stopper bolt (Upper)
(3) Stopper bolt (Lower)
29. Remove the rear roll stopper.
(1) Insulator bolt
(2) Stopper bolt
30. Remove the drive shaft.
31. Remove the front muffler.
32. Remove the sub frame mounting bolt.
33. Install the transaxle jack.
34. Remove the transaxle lower mounting bolt to the engine.
35. Remove the transaxle assembly.

INSTALLATION
Installation is the reverse of the removal.

Then inspect and replace the clutch place and pressure plate.

INSTALLATION
1. Apply multipurpose grease to the release bearing contact surfaces and the release cylinder contact surface of the clutch release fork assembly.
When installing the clutch, apply grease to each part, but be careful not to apply excessive grease. It can cause clutch slippage and judder.
2. Apply multipurpose grease into the groove of the release bearing.
3. Apply multipurpose grease to the clutch release lever fulcrum contact surface of the clutch release fork assembly.
4. Clean the surfaces of the flywheel and pressure plate thoroughly with fine sandpaper or crocus cloth, and make certain that all oil or grease has been removed.
5. Apply a small amount of multipurpose grease to the clutch disc splines and input shaft splines.
Do not apply more grease than necessary. Too much grease could cause clutch slip or judder.
6. Using the special tool, install the clutch disc to the flywheel. When installing the clutch disc, be sure that the surface having the manufactures stamp is towards the pressure plate side.
7. Install the the clutch cover assembly onto the flywheel and install the six (6) bolts through the clutch cover into the flywheel.
8. Tighten the bolts by one or two turns at a time, in succession, to avoid bending the cover flange.
If a special tool is not available, tighten the bolt temporarily and then torque to specification in diagonal torquing sequence indicated below.
TIGHTENING TORQUE
Single mass flywheel:
15~22 N·m (150~220 kg·cm, 11~16 lb·ft)
Dual mass flywheel:
20~27 N·m (200~270 kg·cm, 14~19 lb·ft)
9. Remove the special tool.
10. Install the transaxle. (Refer to GROUP - Manual Transaxle Assembly)
11. Adjust the clutch pedal free-play. (See CH-6)
INSPECTION
1. Check the diaphragm spring end for wear and uneven height.
Replace if wear is evident or height difference exceeds the limit.
2. Check the pressure plate surface for wear, cracks and color change.
3. Check the rivets for looseness and replace the clutch cover assembly if necessary.
CLUTCH DISC
1. Check the clutch facing for loose rivets, uneven contact, deterioration due to seizure, adhesion of oil, or grease, and replace the clutch disc if defective.
2. Measure the rivet sink and replace the clutch disc if it is out of specification
3. Check for torsion spring play and damage and if defective, replace the clutch disc.
4. Clean the splines on the input shaft and install the clutch disc.
If the disc does not slide smoothly or if play is excessive, replace the clutch disc and/or the input shaft.
CLUTCH RELEASE BEARING
The release bearing is packed with grease. Do not use cleaning solvent or oil.
1. Check the bearing for seizure, damage or abnormal noise. Also check the diaphragm spring contacting points for wear.
2. Replace the bearing if the release fork contacting points are worn abnormally.
INSTALLATION
Installation is the reverse of the removal.
Then remove pressure plate and Clutch plate.

1. Insert the special tool (that came with your clutch kit) in the clutch disc to prevent the disc from falling.
2. Loosen the bolts that attach the clutch cover to the flywheel in a star pattern.
3. Loosen the bolts in succession, one or two turns at a time, to avoid bending the cover flange.

on Jan 13, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

How clutch replacement


disconnect battery, remove starte motor, remove drive shafts, support and remove cross member,remove clutch slave cylinder, remove bellhousing bolts and while suspending transmission remove and lower transmission.//remove preasure plate and clutch. Good idea to replace spigot bearing and throw out bearing while you do job. allow 4-5 hrs for r&r. Refit in reverse order.

Nov 17, 2012 | 1987 Toyota 4Runner

1 Answer

How do I replace a clutch 2000 eclipse


Remove transaxle. Remove clutch pressure plate. Remove clutch plate. Inspect the flywheel for damage and resurface or replace as necessary. Replace pilot and throwout bearings. Install new clutch plate. Install new pressure plate. Re-install transaxle.

Mar 06, 2012 | 2000 Mitsubishi Eclipse

1 Answer

HOW TO REPLACE CLUTCH FAN


to remove clutch fan you need to remove upper fan shroud, you need large wrench to remove the fan clutch retaining nut to remove fan and clutch away from the engine drive belt should keep pulley from turning while loosen fan clutch retaining nut.if pulley belt turns while loosen fan clutch bolt remove drive belt use strap wrench hold pulley while you remove fan clutch bolt this procedure for checvrolet if you working on volkswagon you need spanner wrench hold the idler pulley while you use large wrench to loosen the large drive nut to fan clutch. you have to remove fan with clutch from engine then you can remove clutch from fan you can go to auto parts stores rent a spanner wrench try auto zone they rent out tools.

Jan 05, 2012 | Cars & Trucks

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.


TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Mar 15, 2011 | 1995 Ford Econoline

1 Answer

How do you remove the flywheel when replacing the clutch


Unless there is something wrong with the flywheel there is no need to remove it.All that is needed to replace the clutch is to remove the pressure plate and the clutch will fall off. But if the flywheel must be removed just remove the six bolts holding it to the crankshaft after removing the clutch.


bigc

Jul 01, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

1 Answer

Clutch repair 2005 VW Chico


You need to empty the engine from all fluids, tehn remove air filter and other parts, mount your Golf on a bridge and remove the clutch pressure plate assembly mounted on a side of the engine.

You will need special tools to align and mount the new pressure plate, and you will need to follow a procedure to reinstall the clutch without removing the transaxle.

Replacing the clutch is not an easy task for a beginner, if you do it yourself, get the haynes manual with the complete illustrated procedure.

After replacing you will have to adjust the clutch. See CLUTCH REPLACEMENT PROCEDURES.


Feb 17, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...