Question about Cars & Trucks

Open Question

I have a 2009 Town and Country LX and with 2 working fabik keys and it will not enter self-program mode, to add a third key, with the proper instructions.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 Town & Country ignition switch locked

you need to call a locksmith to come to your home. They will replace one or more of the tumblers/cylinders inside the ignition key area. The EXACT same thing happened to me. The Chrysler dealership wanted to charge me over $400 to fix the problem. My wonderful mobile locksmith knew exactly what was srong the nanosecond I mentions the make and model! $49.00 later - FIXED! good luck!

Posted on Mar 12, 2009

Ad
  • 323 Answers

SOURCE: Town & Country 2007 LX model aircondition not working

It does have air conditioning installed. It may also have rear a/c. The rear a/c evaporator is probably leaking freon. I have replaced many rear evaporators on 2006 and 2007 Chrysler minivans as a result of a design change in 2006. Recharge the a/c and add dye to the system. If it has rear air, look behind the right rear wheel in the fender area under the car where the a/c lines go into the body.

Posted on Apr 21, 2009

baccardo
  • 150 Answers

SOURCE: Programming a key fob

you will need the dealership diagnostic tool to program the remote

Posted on Apr 24, 2009

  • 750 Answers

SOURCE: Problem with 2002 Nissan Almera Key Fob

check the battery in the key control it may be faulty

Posted on Jul 21, 2009

  • 150 Answers

SOURCE: In following the Chevrolet Tahoe instruction to program a garage door opener, I am having problems with the system working. The codes are the rolling key type.

Press the outer 2 buttons untill the bink rate changes then release.

Press the button you want to train at the same time you hold down an unused button on one of your factory GDO remotes, hold untill flash rate changes.

Press learn button on GDO, press the button you just programmed in the Tahoe, should be programmed.

(Info should be in users manual under HomeLink.)

Posted on Aug 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you rekey a new ignition key to the original key on a 1999 town car


Maybe. If you have two keys that are already programmed into the computer you can add a third. If not, you'll need a very good locksmith or the dealer with the scanner to change the computer settings.

Aug 05, 2014 | 1999 Lincoln Town Car

1 Answer

CAN NOT PROGRAM NEW KEY FOR 2008 TOWN AND COUNTRY


RESET AND REPROGRAM ALL KEYS, CAN ONLY DO A SET NUMBER, I THINK 8 KEYS. START OVER CLEAN

Mar 12, 2014 | 2008 Chrysler Town & Country

1 Answer

Key stuck in ignition of 2009 chrysler town and country


Try to start it in neutral. If it starts then it sounds like a neutral safety switch. If the battery is dead it may not let the key out unless you jump the van.

Mar 01, 2013 | 2009 Chrysler Town and Country

1 Answer

T & C 2001 REMOTE CONTROL PROGRAMMING


ATTENTION: You MUST HAVE one working remote to add one more to the system.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. A chime will sound afer each
additional remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.

Sep 17, 2012 | 2001 Chrysler Town & Country

1 Answer

Car says bad key when key is put into ignition what do i do/


sounds like the computer may be having a problem reading the code that is keyed in for the key its self - ay have to take it to a dealer for more information

Jul 22, 2012 | 2009 Chrysler Town and Country

1 Answer

Alarm button broken. Cannot disarm alarm. What do I do? Chrysler Town & Country LX 2003 model.


You can arm or disarm alarm manually with the key at the drivers side door, turn the key to open the locks and the alarm must be disarmed.

Nov 01, 2010 | 2003 Chrysler Town & Country

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

1 Answer

Program a transponder key


this must be done by the dealer.

Mar 21, 2009 | 2006 Chrysler Town & Country

1 Answer

2003 chrysler town & country speedometer stuck


sit in the drivers seat close the door. with the key off hold the trip odometer button in then while holding the button in turn the key on. if done correctly this will put the MIC (mechanical instrument cluster) into a self test. if the speedometer does not move like the rest of the gauges during this test the MIC must be replaced. if the speedometer does move it is likely your problem will be fixed, however, if the speedometer does move but it does not start working properly then further diagnostic will be needed.

Mar 19, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...