Question about Cars & Trucks

Open Question

In assembling the bike, the lower computer post cover was put on before thecomputer post was screwed in. I now cannot get the lower post cover off and therefore cannot continue assembling the bike

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can undo the trim around the radio of montana 2004 to replace radio of montana 2004 Van


1. Open cup holder and remove (2) Phillips 7mm screws.

2. Unsnap and remove power outlet assembly from lower storage, unplug power outlet wires and put assembly in a safe location.

3. Open lower storage door and remove (2) 7mm screws inside.

4. Models with DVD - Remove DVD player and remove (2) 7mm screws from behind and (2) 7mm screws near the floor.

5. Remove lower storage compartment, put it in a safe location.

6. Remove (2) 7mm screws (facing up) from the cup holder.

7.Remove (3) 7mm screws and remove radio.

Dec 06, 2014 | 2004 Pontiac Montana

2 Answers

How to remove the ignition lock cylinder from a 93 geo storm


is the lock assembly in the car or out?
there are 2 jobs here, removing the assembly
and after that, attacking the lock it self.???????

any lock smith can rebuild the lock, proper
it has pins that are pressed out.
it can even be rekeyed.

the remove assembly is covered in the FSM, no books?
alldata.com covers that.
it really is an Isuzu. impulse.

my guess is its job 1, assembly out.
so toss coin lands on job1
(on most cars, steering wheel must be removed)
once that is done, its obvious from there, right? that clamp there with the antitamper screws? then must be removed. and replaced new..

a rare car , and even more one that runs....

here is the online FSM answer

  1. Remove the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch assembly.
  4. Turn the key to the OFFposition, depress the retaining pin and remove the ignition lock cylinder from the switch.
  5. Disconnect the electrical connector from the ignition switch.
  6. Remove the snapring and spacer collar from the steering shaft.
  7. Disconnect the back drive cable from the ignition switch.
  8. Remove the ignition switch bolts and the ignition switch from the steering column.


now back in?
  1. Install the ignition switch to the steering column and tighten the bolts.
  2. Connect the back drive cable to the ignition switch.
  3. Install the spacer collar and the snapring to the steering shaft.
  4. Connect the electrical connector to the ignition switch.
  5. Install the lock cylinder into the switch.
  6. Install the turn signal switch screws and the turn signal switch.
  7. Install the four screws and the coil assembly to the turn signal switch.
  8. Connect the coil assembly wiring harness to the turn signal switch.
  9. Install the two piece steering column cover and the two piece steering column cover screws.
  10. Raise the steering column and install the upper steering column mounting bolts. Tighten the bolts to 18 ft. lbs. (24 Nm).
  11. Install the left lower dash trim panel and tighten the lower dash trim panel screws.
  12. Install the lap air deflector and tighten the lap air deflector screws.
  13. Install the knee pad assembly and tighten the five screws, the bolt and the nut attaching the assembly.
  14. Install the engine hood opener cable.
  15. Install the engine hood opener and tighten the two screws.
  16. Connect the electrical connector to the cigar lighter bezel and install the bezel.
  17. Connect the electrical connector to the left switch bezel and install the bezel.
  18. Install the steering wheel.
  19. Connect the negative battery terminal to the battery.

that?

Oct 08, 2014 | 1993 Geo Storm

1 Answer

Ignition key assembly is locked up. bought a new one but have never changed one. got any instructions and/or diagrams to help me? It's a 1989 Plymouth Voyager 3.0 motor Tilt steering column with shifter on...


Take out the screws holding the upper and lower plastic column covers together. Pull the lower cover off. Now look at the ignition switch mounting bolts, they are anti theft. If you go to "Tools n More" or "Harbor Freight Tools" you should be able to purchase the special anti-theft tip you need in a set to take the screws out. Once you have unbolted the switch putting in the new one is easy.

May 05, 2011 | 1989 Plymouth Voyager

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

How do I replace the heating fan on my 2000 Kia sportage


Blower Motor
Removal & Installation
To Remove:


  1. Evacuate and recover air conditioning refrigerant.
  2. Remove battery.
  3. Disconnect and cap A/C lines at evaporator tubes.
  4. Remove blower motor assembly drain.
  5. Remove glove box.
  6. Remove 5 screws and right hand instrument panel lower trim panel.
  7. Remove screw that attaches upper center console to gain access to left
    instrument panel lower support.
  8. Remove left and right bolt and remove instrument panel lower support.
  9. Detach control cable from inlet duct.
  10. Disconnect blower motor electrical connector.
  11. Pull carpet back and remove hole cover plate.
  12. Remove 2 bolts at top of blower motor assembly.
  13. Remove 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  14. Remove blower motor assembly.

To Install:


  1. Install blower motor assembly.
  2. Install 2 bolts at top of blower motor assembly.
  3. Install 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  4. Install hole cover plate and replace carpet.
  5. Connect blower motor electrical connector.
  6. Install instrument panel lower support and install left and right bolts.
  7. Install right hand instrument panel lower trim panel and 5 screws.
  8. Install glove box.
  9. Install blower motor assembly drain hose.
  10. Connect evaporator lines at bulkhead.
  11. Evacuate and charge air conditioning refrigerant.
  12. Install battery.

Oct 29, 2010 | 2000 Kia Sportage

2 Answers

Need to remove ignition switch in my 1986 cutless to put new one in. how do I remove the old one.


Removal & Installation
NOTE This is an extremely difficult and lengthy procedure. You must remove the steering column from the vehicle and disassemble major portions of it. Because the column is collapsible in an accident, it is necessary that it be handled with care to avoid distortion of major parts. It must not be dropped, hammered on or even leaned on, or vitally important parts may deform. The procedure for replacing the ignition switch on tilt type columns is not included here because it involves substantial additional work and the use of several expensive special tools. Unless you are rather experienced, we recommend that the job be left to a competent professional mechanic.

  1. Disconnect the negative battery cable. Remove the clamp bolt from the steering coupling at the lower end of the steering column shaft (located near the steering box, under the hood).
  2. Disconnect the shift linkage from the shift tube lever at the lower end of the column.
  3. Remove the steering wheel with a puller, as described above.
  4. Remove the left sound insulator and lower column cover.
  5. Remove the trim cap or lower trim panel from the instrument panel, depending on equipment.
  6. Remove the steering column cover and toe-pan attaching screws. Remove the shift indicator needle from the shift bowl.
  7. Securely support the column in position and remove the two nuts attaching the column to the underside of the instrument panel.
  8. Lower the column carefully, being careful to retain any spacers that may have been used in order. Disconnect the wiring. Then, carefully remove the column from the inside of the vehicle.
  9. Begin disassembling the column, removing the lock plate, canceling cam, and turn signal switch. See the "Turn Signal" Removal & Installation procedure above.
  10. Remove the ignition lock and key warning switch as described below.
  11. Remove the spring and bolt assembly, and the associated thrust washer. Then, remove the rack preload spring, switch rack, and actuator assembly.
  12. Remove the upper shift lever spring. Then, remove the gear shift lever bowl.
  13. Remove the shift bowl shroud and bowl lower bearing.
  14. Unhook and remove the dimmer switch actuating rod. Remove the attaching nut and remove the dimmer switch.
  15. Remove the attaching screw and stud and remove the ignition switch, disassembling the actuating rod from the hole in the sliding actuator.

43e5d01.gif
Replacing the ignition switch

To install:
  1. Move the ignition switch sliding actuator all the way to the left (ACC) position. Then, move it two detents (OFF-UNLOCK) position to the right.
  2. Then, position the actuating rod hole in the sliding actuator, and install the ignition switch, stud, and mounting screw.
  3. Install the dimmer switch with its attaching nut tightened only loosely. Then, depress the switch slightly until you can insert a 3/32 in. drill through the hole in the switch housing and slider. Force the switch upward to remove any lash and tighten the mounting screw with the switch in this position.
  4. Put the shifter in NEUTRAL and install the shift lever.
  5. Install the shift bowl shroud and bowl lower bearing.
  6. Install the rack preload spring, switch rack, and actuator assembly. Install the spring and bolt assembly, and the associated thrust washer.
  7. Install the ignition lock and key warning switch as described below.
  8. Reinstall the column into the vehicle. Make sure when assembling the lower and upper dash covers that they can slide on the column. If the bracket which mounts the column to the dash has been removed, install the bolts in this order:
    • Left rear
    • Left front
    • Right front
    • Right rear
Tighten the bolts just snug to avoid distorting the column.
  1. Install the switch connector to the ignition switch. Then, position the column in the body and support it there. Install the lockwashers and nuts for the coupling and tighten them. Then, loosely assemble the nuts fastening the mounting bracket for the column to the lower side of the instrument panel.
  2. Position the lower cover to the firewall and ensure that the cover is lined up by starting the left lower screw. Then, install and tighten the right lower screw. Then, tighten the left lower screw. Finally, install and tighten the two screws that fit into the top of the cover.
  3. Tighten first the screw for the left side of the cover clamp; then tighten the screw for the right side of the cover clamp. Finally, install and tighten the remaining cover screws.
  4. Finally, tighten the nuts fastening the column to the underside of the dash. Reinstall the bolt for the steering coupling clamp.
  5. Install the lock plate, canceling cam, and turn signal switch. See the "Turn Signal" Removal & Installation procedure in this section.
  6. Connect the wiring.
  7. Securely support the column in position and install the two nuts attaching the column to the underside of the instrument panel.
  8. Install the shift indicator needle from the shift bowl. Install the steering column cover and toe-pan attaching screws.
  9. Install the trim cap or lower trim panel to the instrument panel, depending on equipment.
  10. Install the left sound insulator and lower column cover.
  11. Install the steering wheel, as described above.
  12. Connect the shift linkage to the shift tube lever at the lower end of the column.
  13. Install the clamp bolt to the steering coupling at the lower end of the steering column shaft (located near the steering box, under the hood).
  14. Connect the negative battery cable and check all column operations for free movement and smooth operation.

Feb 15, 2010 | 1986 Oldsmobile Cutlass Supreme

1 Answer

I have a 96 mercury mark 5, when i press the brake it wont shift out of park. It was intermedeit now its just locked.


This is the procedure for a 93 Marquis, should be similar, hope it helps.
Brake Shift Interlock Solenoid

Removal
1. Disconnect battery ground cable and air bag backup power supply.

2. Remove lower RH and LH mouldings from instrument panel by pulling up and snapping out of retainer.

3. Remove five retaining screws from instrument panel lower cover and remove cover.

4. Remove instrument panel reinforcement.

5. Disconnect transmission range selector cable from actuator housing by removing one screw.

6. Remove four column attaching nuts and lower column assembly.

7. Remove electrical harness from brake shift interlock (BSI) solenoid assembly.

8. Remove three screws attaching BSI solenoid and insert plate to column assembly and remove solenoid and insert plate. Separate solenoid from insert plate by removing tinnerman clip.

Installation
1. Position BSI solenoid and insert plate in place and attach to column assembly with three screws as shown.

2. Connect electrical harness to BSI solenoid.

3. Attach column assembly to half car beam with four nuts.

4. Connect transmission range selector cable to column assembly with one screw.

5. Attach instrument panel reinforcement brace with three bolts.

6. Attach instrument panel lower trim cover with five bolts.

7. Install RH and LH mouldings on instrument panel.

8. Connect air bag backup power supply and battery ground cable.

Oct 24, 2009 | 1986 Mercury Marquis

2 Answers

How do you change the heater core in a 2002 Dodge Intrepid?


  1. Disconnect the negative battery cable from the remote battery post located near the right strut tower.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
    Remove the instrument panel by removing or disconnecting the following:
  2. NOTE On the LHS or 300M, remove the center bezel prior to the shifter bezel
    Shifter knob Allen screw Both instrument panel end covers Using a trim stick tool, gently pry upward on the shifter bezel; then, disconnect both wiring connectors and a light bulb socket connector; then, remove the socket.
  3. Remove the 2 lower instrument panel cover screws (outside end) and disconnect the deck lid release switch wiring connector. Pull the lower instrument panel cover rearward releasing the clips. Remove the cable-to-brake release handle. Pull the cover rearward and remove it.
  4. If equipped for 6 passengers, remove the lower floor bin.
  5. If equipped for 5 passengers, remove or disconnect the following items:

    Center bezel using the trim stick Heater/air conditioning housing assembly control switch and the traction control switch wiring harnesses Bezel from the vehicle Two left side console side cover screws, pull the cover outward and remove from the vehicle Lower glove box door; the 2 screws are located at the right console side cover, pull outward and remove it 2 bracket screws and the 2 inside the console bin; then, remove the console 2 center lower instrument panel nuts 4 steel reinforcement-to-lower instrument panel cover bottom bolts 16-way DLC from the reinforcement left floor duct/silencer pad screw and the pad Steering column shrouds Shift interlock cable at the ignition switch Column wiring The under column duct section Left panel air conditioning outlet duct The 4 brake pedal support bracket-to-column mounting bolts Lower the steering column Heater/air conditioning housing and the Air bag Control Module (ACM) harness connectors then, the 2 ground eyelets from the floor tunnel near the bulkhead Using a trim stick, carefully, pry out on the left and right A-pillar trim moldings and slide them rearward to remove them.
  6. Using a trim stick, carefully pry upward on the instrument panel top cover, and remove it.
  7. From both sides, remove the scuff plate screw. Using a trim stick, carefully, pry out the scuff plates and remove them.
  8. Remove or disconnect the following:

    3 right side cowl panel screws and the panel 3 left side cowl panel screws and the panel Remove the right side under dash silencer and pad 2 right side radio antenna and amplifier harness connectors Left side junction block and Body Control Module (BCM) harness connectors 8 instrument panel-to-chassis screws Pull the instrument panel rearward Instrument panel from the vehicle with the help of an assistant ischarge and recover the air conditioning system refrigerant.
  9. Drain the cooling system into a clean container for reuse.
  10. Place shop cloths in the interior to catch any excess coolant.
  11. Remove or disconnect the following:
    WARNING The air conditioning lubricant used in this system absorbs moisture readily. Do not leave any portion of the system open for any long period of time.


    Air cleaner hose and the air distribution duct Heater hoses-to-dash panel spring type fasteners and the heater hoses from the heater core. Plug the openings to prevent coolant spillage. Refrigerant lines-to-expansion valve nut and separate the refrigerant lines from the expansion valve. Plug the openings to prevent contamination. 3 heater/air conditioning housing assembly-to-chassis nuts from the engine compartment 2 defroster duct screws and the duct Heater/air conditioning housing assembly-to-dash panel nuts and screws 4 rear seat heat duct nuts and the duct Rear seat heat duct elbow push-pin fastener Electrical connector from the heater/air conditioning housing assembly Pull the heater/air conditioning housing assembly rearward and remove it from the vehicle 2 heater core-to-heater/air conditioning housing assembly screws Heater core from the heater/air conditioning housing assembly
contact me and i can tell you how to put it back together

Jun 28, 2009 | 2002 Dodge Intrepid

1 Answer

Removing ignition switch


Grand Am 3.1 liters REMOVE Negative battery cable. Air bag fuse. Lower left insulator panel (3) screws. Disconnect 2-way yellow SIR connectors (2). Tilt lever. Upper and lower steering column trim cover. Turn lock cylinder to run position. Push against locking button on back side of bearing and housing assembly and remove lock cylinder. INSTALL Lock cylinder to housing assembly. CAUTION : Rotate the lock cylinder to the "RUN" position. Depress the lock cylinder button. Gently push the lock cylinder into place while rotating the key approximately 5°in the counter-clockwise direction. Upper and lower column cover (3) Torx(R) screws. Tilt lever. Connect 2-way yellow SIR connections (2). Lower left insulator panel (3) screws. Air bag fuse. Negative battery cable.

Jun 11, 2009 | 1998 Pontiac Grand Am

4 Answers

Replacing a brake light bulb for a 2006 chevrolet equionx


I just replaced the p/s brake light:
1. Pop off the tabs that cover the screws. (flat screwdriver)
2. Unscrew both screws. (philips-head)
3. There is a metal post attached to the light assembly located towards the front of the assembly pointing in towards the center of the car. This post fits into a rubber grommet that is attached to the car. I had to wiggle and rock the assembly to get the post free from the grommet and the assembly off the car, by pulling to the right.
4. Re-assembly requires lining up and inserting the post back into the grommet (use your best Beavis and ******** sound effect now). Put the screws back in and don't forget the covers.

Jun 20, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...