Question about Ford Cars & Trucks

1 Answer

Wiring schematic 92 Ford Aerostar with TBS0073 starter motor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 126 Answers

Http://quickmanual.blogspot.com/2012/01/ford-aerostar-system-wiring-diagram.html

Posted on Apr 22, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am in need of under dash fuse panel diagrams backside power side 92 Ford ranger xlt.


Confused by 'backside power side', but

Just Google

92 Ford Ranger XLT fuse box
And look at the Inage tab.

Or if you are after wiring details

92 Ford Ranger XLT wiring schematic

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

Replace starter on ford Aerostar 3.0


Please see my tip at http://www.fixya.com/cars/r5973094-starter_replace . These are generic instructions. Specific instructions for your car from autozone.com are pasted below.


REMOVAL & INSTALLATION
See Figures 4, 5 and 6

  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support it safely on jackstands.
  3. Disconnect all cables and wires at the starter solenoid on the starter motor.
  4. Remove the starter mounting bolts and lower the starter from the engine.

eeea2a6.gif


Fig. Fig. 4: Detach the wiring connectors from the starter motor, ...


fa8b115.gif


Fig. Fig. 5: ... then, while supporting the starter motor, remove the starter mounting bolts


d8861ce.gif


Fig. Fig. 6: Lower the starter motor out from under the engine-1991 3.0L engine shown, other engines similar


To install:

  1. Position the new starter assembly to the engine block and start the mounting bolts in by hand.
  2. Snug all bolts while holding the starter squarely against its mounting surface and fully inserted into the pilot hole. Tighten the mounting bolts to 15-20 ft. lbs. (21-27 Nm).
  3. Reconnect the starter cables and wires to the starter motor. Tighten the screw and washer assemblies to 70-130 inch lbs. (8-15 Nm).
  4. Lower the vehicle, then connect the negative battery cable.
When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 10 miles (16 km) or more for the PCM to relearn the strategy.

Oct 20, 2010 | 1995 Ford Aerostar

1 Answer

Changing the spark plugs and wires on a 92 ford aerostar getting to the back 2 plugs can't find a way to get back to them


Remove the upper motor mount's bolt(s) & rotate the engine forward. When done rotate back & replace bolt(s). Easy. Good luck!

Sep 03, 2010 | 1992 Ford Aerostar Extended

1 Answer

Need help with a clockspring wiring connection on my 92 aerostar.


That wire if it is black and pink goes to the igntion tumbler. chime. remove the tumbler to install.

Sep 30, 2009 | 1992 Ford Aerostar Extended

1 Answer

I have a 92 Ford Aerostar no injector pulse!


OK YOU HAVE SPARK IN THE WIRES AND YOU DO HAVE GAS TOO AND THE CAR DOESNT START OR THE ENGINE DOESNT TURN OVER

Jul 30, 2009 | 1992 Ford Aerostar Extended

1 Answer

Need schematic for ignition system-has 4 wire dist. pickup and ignition module is mounted on the R/F fender


Resistive cottection between PIP (pin6) wire and connector at the ignition module. Cleaned and soldered wire to connector pin. Runs fine.

May 25, 2009 | 1991 Ford Aerostar Extended

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...