Question about Buick Cars & Trucks

1 Answer

Is there a video to show me how to do a valve job on a 2002 buick rendezvous

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 11,043 Answers

Do you have a valve grinder , seat grinder ? Casting 441 Ported Head TRUE Three Angle Valve Job 9

Posted on Apr 22, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to take the engine out in a 2002 buick rendezvous to do a valve job


probably not a valve problem but a firing order problem
run a compression test to check for valve and head problems before you waste time and money of the engine
could be a injector leaking

Apr 22, 2017 | Buick Cars & Trucks

1 Answer

What is the alternator fuse number for 2002 Buick rendezvous


It's a fusible link , do you know what it is ? Here is a youtube video showing location of fusible link . On the video he talks at the vehicle starting , alternator gets power the same way. How to Replace Fusible Link Car won Start If you pull on it an the insulation stretches it's brunt inside .
Fusible Link
In line to the generator, near the positive battery cable
Did you check for B+ voltage at the heavier gage wire on the back of the alternator ? The turn on signal comes from the PCM - engine computer .

Oct 08, 2016 | 2002 Buick Rendezvous

1 Answer

P0412 valve a problem where is valve a located on a 2002 buick rendezvous


This is the electrically driven secondary air injection air pump. Please read all the information at the link before you buy or replace any parts. In most cases the entire air injection pump assembly must be replaced.
P0412 Secondary Air Injection System Switching Valve Circuit Malfunction

Jul 06, 2016 | 2002 Buick Rendezvous

1 Answer

Buick rendezvous 2002 from wheels, have 2 codes PO446 PO453


code p 0446 refers to evaporative emission (EVAP) system---vent control---circuit malfunction===causes --wiring---EVAP canister purge valve ---ECM
replace the purge valve
code p 0453 refers to EVAP pressure sensor --high input ===causes --wiring short to positive --EVAP pressure sensor ---ECM
replace the sensor

Nov 02, 2015 | 2005 Buick Rendezvous

1 Answer

How to change shaft stabalizer bar on 2002 buick rendezvous


The stabilizer bard rarely need replaced. There 2 brackets holding the bar in place. They both have a bushing that goes bad from time to time. The real issue with the stabilizer bar is the end- the stabilizer rods on the ends. You can usually replace these in about 1/2 hour and the job is done. Go to your local parts store and order the stabilizer rod and bushing kit, The kit will come with an in instruction sheet, and it is a very simple job.

Dec 31, 2014 | 2002 Buick Rendezvous

1 Answer

Where is the oil pump in my 2002 buick rendezvous


Before replacing the oil pump, which is a huge job, I would have someone check the actual oil pressure with a mechanical gauge. It is more likely a bad sending unit.

Feb 02, 2013 | 2002 Buick Rendezvous

1 Answer

I just replaced the the intake manifold gasket in my 2002 Buick Rendezvous with a 3.4 v-6. My question is about the lifters, what should they be set at? Do you just tighten them down? Thank You


The lifter have to be set. If you tighten them down on the wrong stroke, The vales have a certain lash (measurement) to be set at.it will cause your car to skip. not run correct or even damage to the engine. The best tip I can give to be instructional is to visit YOUTUBE and look up valve adjustment and it will show you how to perform this task. Good Luck.

May 09, 2010 | 2002 Buick Rendezvous

1 Answer

Replaced the fuse for my 2002 buick rendezvous cigarette lighter, but it blows every time I plug in my phone charger into the lighter.


Have you tried plugging something else into the socket before the phone charger? Try that and see if it blows as it could be the phone charger. If it does then you will need to replace the socket. Its an easy job and they are cheap.

Jan 06, 2010 | 2002 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...