Question about Mazda Cars & Trucks

Open Question

My mazda rustler 160i wont start when switch off and I try to start it again.I had to close the fuel line and start

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
WildBill49
  • 97 Answers

SOURCE: mazda rustler 160i

Hi Gerrie1974-

WildBill49 here......Not knowing the specific year and version of your Mazda, I cannot give you a specific part at fault, but I can help you. I am assuming we're talking about an electronic distributor single coil ignition system

If the spark is weak directly out of the coil (with a known good coil hooked up with correect polarity), then the problem is in the spark trigger module... There is a variety of designs, but the basic components remain the same. This is the part of the ignition system that replaces the breaker points. It consists of two parts - a magnetic spark trigger sensor, and a spark signal amplifier/controller. these are sometimes combined into one ignition module.

Replace this module, and spark from the coil should be strong! If it is still weak, reverse the two wires to the coil.

Weak spark at the plug wire with the above good indicates distributor cap/rotor replacement time...

Gerrie, I hope this is what you are looking for, best of luck, and if you feel my advice worthy, please rate it!!!

Thanx-
-WB

Posted on Jun 22, 2008

Ad
  • 1 Answer

SOURCE: mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Posted on Dec 17, 2008

  • 2 Answers

SOURCE: 1997 mazda rustler 160i wheel bearings

buy a chevy

Posted on Dec 19, 2008

  • 1 Answer

SOURCE: where do i get fuel pump in mazda rustler 160i

fuel pump located inside petrol tank,
you have to remove the fuel tank, only 4 bolts, and a few pipes.
befor doing so, check fuel pump relay located in the middle of dashboard on the floor(horse shoe type plastic cover)

Posted on Nov 26, 2009

dcramer531
  • 1654 Answers

SOURCE: Fuel does not come from

Either your fuel pump has died, make sure you check all fuses and wiring for shorts, or the screen on the pump is clogged and needs to be cleaned. Most likely the pump needs replaced and the t ank will have to be lowered to acces the pump.

Posted on Mar 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda Rustler 160i Has been running perfectly. All of a sudden cuts out and now won't start. Fuel problem? Dirt? Not familiar with fuel injection


a blocked fuel filter will give a starving indication well before it gets to clogged to pass fuel
the problem is else where
run the fault codes to determine the problem sensor

Feb 16, 2017 | Mazda Cars & Trucks

1 Answer

My Mazda Rustler 160i 1998 Bakkies fuel injectors don't open,What is the problem


First, test fuel pressure as injectors will not open if pressure is low.

Aug 01, 2016 | Mazda Cars & Trucks

1 Answer

My mazda rustler 160i only start normally when the petrol tank is on empty,i don't understand why.


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

May 12, 2016 | Mazda Cars & Trucks

1 Answer

What's your question?if i want to convert mazda rustler 160i 1997 model b6 from injectors to caburator what to replace and how much is the caburator?


Hi u will need a intake manifold and a carb .it will cost u about R3400 but Y do u want to put a carb on a fuel injected car

Jun 14, 2015 | Mazda Cars & Trucks

1 Answer

Mazda rustler 160i starts idles but when reving or bringing the revs up starts to splatter and jurk and petrol vapour is strong as well as backfire throu intake and when revs are droped throu exhoust. pls....


ck your distributor, the cap and rotor, if all are good ck timing to see if jumped time. if in time and distributor ok ck fuel, and look for vacuum leaks.

Aug 19, 2012 | Mazda Cars & Trucks

1 Answer

Fuel does not come from the tank on amazda rustler bakkie 160i 2001 model hence the car cannot start


Either your fuel pump has died, make sure you check all fuses and wiring for shorts, or the screen on the pump is clogged and needs to be cleaned. Most likely the pump needs replaced and the t ank will have to be lowered to acces the pump.

Mar 31, 2011 | Mazda MPV Cars & Trucks

1 Answer

Where do i get fuel pump in mazda rustler 160i


fuel pump located inside petrol tank,
you have to remove the fuel tank, only 4 bolts, and a few pipes.
befor doing so, check fuel pump relay located in the middle of dashboard on the floor(horse shoe type plastic cover)

Jun 24, 2009 | 1987 Mazda 323 4-Door

1 Answer

Mazda rustler 160i wheel bearings


a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...