Question about Cars & Trucks

Open Question

How do you replace a crank shaft sensor on a 2005 pt cruise

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

c17hydro
  • 2984 Answers

SOURCE: Crank shaft sensor

If it is the front wheel drive model, it is in the back side of the motor looking up at it....simple to change.....the side that faces the cab of the vehicle.

Posted on Mar 05, 2009

emissionwiz
  • 75066 Answers

SOURCE: Where is crank sensor on

REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Posted on Aug 22, 2011

emissionwiz
  • 75066 Answers

SOURCE: 2004 chrysler sebring 2.4l dohc.

Have you ever replaced the timing belt?? If not the problem is likely to be a loose worn out timing belt. A floppy belt will play havoc with the sensor signals and trigger a check engine light and a camshaft sensor code.

Posted on Jun 22, 2012

aguero1984
  • 1 Answer

SOURCE: 2005 kia sorento crank shaft position sensor

I HAVE A 2005 KIA SORENTO V-6. MY PROBLEM STARTED WHEN I WOULD DRIVE ON TO THE HWY IT WOULD PUTTER LIKE IF I WAS LOSING POWER. THE HOLE TIME THIS WAS GOING ON MY GAS GAGE WOULD NOT WORK. SO I WENT OUT TO AUTO ZONE HERE IN MADERA CA AND BOUGHT A DIAGNOSTIC TESTER AND THE CODE NUMBER P0338 WHICH MEANS CRANK SHAFT CENSER IS GONE. SO WHEN YOUR GAS GAGE STOP WORKING GET YOUR CAR TESTED OR THE BEST WAY TO GO IS TO INVEST IN A DIAGNOSTIC TESTER. IT WILL SAVE YOU A LOT OF MONEY

Posted on Jul 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does check engine light come back on after replacing crank sensor


The check engine light is still on because the fault identified by the computer was not caused by a failed crank position sensor.

Mar 01, 2016 | 2005 Chrysler PT Cruiser

2 Answers

My pt cruiser has code 1391. i changed cam sensor crank sensor wires plugs and coil still getting 1391 code and from 0 mph to 20 mph car skips and revs up any ideas?


The cam and crank sensors have the same power wire. Go after that one. They also have the same ground, but other sensors connect to it also. So it's not the ground. And they have separate return signal wires. Not them either.

Mar 09, 2015 | 2001 Chrysler PT Cruiser

1 Answer

Gets no spark when trying to start it


Check to see that there are no blown fuses.
If you have no spark most likely it has to do with the Crank Shaft Sensor. There is a know problem with PT Cruisers. there is a wiring harness the is above the CV shaft to the right front wheel. it can come loose and rub on the CV shaft. you have to look at it from under the car. check to see if any wires have worn through. Thar harness has wires that go to the Crank sensor. if you find wires worn through all you need to do is repair the wires. If you find no wires worn through or rubbing I would replace the crank sensor.

Hope this helps

Sep 30, 2012 | 2003 Chrysler PT Cruiser

1 Answer

Were i the crankshaft position sensor located o a 2005 pt cruiser


near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Sep 14, 2010 | 2005 Chrysler PT Cruiser

1 Answer

I need to know where the Cam Shaft sensor is for my 2005 PT Cruiser is. My car is sputtering and the car is not starting when the switch is turn on.


the cam sensor is near the battery. it is on the end of the cylinder head rear. you should have a code po340 if the cam sensor is bad. get someone to scan it before replacing the sensor . check under the car for a wire rubbing on the cv shaft that goes to the crank sensor.

Aug 31, 2010 | 2005 Chrysler PT Cruiser

1 Answer

We just bought a 2006 R/T Hemi V-8 Magnum. The cruise does not work. It worked the other day, but thats it. How can we fix this? I need cruise control!


Its possible that you have a faulty crank shaft position sensor. Mine went out in my 05 RT and the car stalled frequently at stoplights and the cruise control would not work. It could be something else but after replacing my crank sensor I haven't had an issue.

Aug 24, 2010 | 2006 Dodge Magnum

1 Answer

Where is the crank sensor located on 2005 chrysler pt cruiser?


the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Dec 13, 2008 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...