Question about 2001 Honda Odyssey

3 Answers

Remove and replace lug bolts on my 2001odysey

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Honda Master
  • 511 Answers

The old studs can be hammered out and if you have room the new stud can be squeezed back into the hub and pulled through by using an old lug nut (flipped backward) on the treads and a air wrench.PUT A LARGER NUT between the wheel lug nut and the hub when pulling in the stud as some stud threads don't go all the way back to the hub.Look at the back of the hub and watch the stud pull in.When the back of the stud is flush with the hub,STOP.Do not over torque the stud.

Posted on May 06, 2017

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 29 Answers

Jason, im guessing you old ones are either broken or stripped. It will really depend on how long the bolts are.
You can take a punch and hammer, drive out the old ones. If the new ones aren't to long you can slip the new ones in from the back of the hub.
If you are able to slip them in, you can place one of the lug nuts on the stud ( backwards) and proceed to tighten the lug nut until the new bolt completely seats against the hub.
The reason you place the lug nuts backwards is so you don't damage the chamfer,tapered end of the lug nut.

Get back to me if you have any other questions, Robert

Posted on May 05, 2017

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers

Getting the old ones out is the main problem. If you have never worked on a hub before it is a bigger job than you may think.

Posted on May 06, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace lug bolts on my 2001odysey without removing hub


remove the drum or brake disc
use a tool like a ball joint remover clamp to push the broken stud out of the hub
fit the new hud stud and pull it into place
of course it is more professional and quicker to do it with the hub off

Apr 21, 2017 | Cars & Trucks

1 Answer

Replace front brake pads


1. Raise vehicle
2. Support on jack stand
3. Remove lug nuts
4. Remove wheel
5. Remove bolts holding caliper
6. Remove calipers
7. Remove brake pads
8. Push piston into caliper
9. Inspection rotor for damage if damaged replace
10. Install new pads
11a. Replace caliper on rotor
11 b. Replace bolts in caliper and tighten
12. Bleed brakes
13. Replace wheel
14. Replace lug nuts
15. Lower vehicle
16. Tighten lug nuts
17. Test drive vehicle

Oct 17, 2015 | 2004 Chrysler Sebring

1 Answer

The lug bolt broke when i removed the nut. to fix the brakes. how do i get the lug bolt out?


jUST TAKE ALL THE LUGS NUTS OFF & REMOVE ROTOR WITH A 5 LLB SLEDGE HAMMER KNO0CK BROKEN BOLT & REPLACE WITH NEW BOLT

Jun 16, 2011 | 1999 Daewoo Leganza

1 Answer

How to change front brake pads on 2006 town and country


Loosen tire lug nuts. Jack up the car and remove lug nuts and tire. Remove two bolts holding the caliper in place. Remove the the two bolts holding pads in place. Hang caliper with a wire from wheel so brake line is not stressed. Mount new calipers in correctly and tigthen pad bolts. Put caliper on and tighten caliper bolts. Replace tire and lugs nuts. Jack car down and tigheten lug nuts.

Aug 17, 2010 | 2006 Chrysler Town & Country

1 Answer

How do you replace lug nut bolts on a 2004 chevy trailblazer? Two lug bolts have broken off. Do I have to remove disk brakes and how hard is this?


its just esayer to take it to a tire shop the charge like 10 bucks a stud

aslo you have to have a press to press them on o ther thtan that theyr easy to replace

May 14, 2010 | 2004 Chevrolet TrailBlazer

3 Answers

Broken lug nut on right front wheel. Can you buy just one lug bolt and nut. the threads are stripped and they both need to be replaced. what is the procedure to replace the bolt?


hi,
remove the rotor with the lugs in it - take it to NAPA - they will remove the old one and replace it with a new lug bolt/nut combo for the price of the parts. 28ab2be.jpg

Apr 08, 2010 | 1998 Ford Ranger SuperCab

3 Answers

I have sheared a front wheel lug on my 1995 landcruiser Amazon. Friends had a puncture and didn,t tighten wheel nuts properly on spare. How do I replace.


The lug nuts are press fitted in the rotor. You should be able to hit the bolt with a hammer(or hammer and punch if the bolt is sheered flush with the rotor) and it should come out.

Jan 17, 2010 | 1995 Toyota Land Cruiser

1 Answer

Replacing rear lugs


There are 4 bolts holding the wheel bearing/ABS sensor Assembly to the axle housing. Remove them and remove the wheel bearing from the car. You will be able to rotate the spindle and remove the lug studs. To replace them put it in the hole and tighten a lug nut to pull it into place(an impact wrench will be quite helpful). No Hammering it in, as it may dammage the sensor or bearing.

Oct 11, 2009 | 2005 Dodge Grand Caravan

1 Answer

Need to replace broken lug bolt


If you have room behind the broken lug you can usually drive it out with a good smack of a sledge hammer. To re-install, use a stack of washers between the nut and flange and draw the lug into position. (plenty of oil on threads to avoid galling)

Apr 19, 2009 | Toyota Tacoma Cars & Trucks

1 Answer

1990 Sentra How it remove and replace lug studs on front wheel


there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Feb 27, 2009 | 1990 Nissan Sentra

Not finding what you are looking for?
2001 Honda Odyssey Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...