Question about Chrysler Town and Country

Open Question

2005 chrysler town& country 3.8l sat over winter now has no response no key cycle code response will not crank or cycle fuel pump jumping starter will crank over fine no fire or injector pluse

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

Ad
chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

  • 117 Answers

SOURCE: 2005 crank position sensor location

The crank shaft sensor on that model should be on the driver side towards the back of the tranny its not hard to get to.

Posted on Jun 27, 2009

  • 52 Answers

SOURCE: how do i replace a fuel pump on a 99 chrysler town

the fuel pump is in the gas tank. you will have to remove the bolts that hold the straps in place, lower the tank a few inches as to easier access to the fuel lines and wiring harness. unhook all the wiring and the fuel lines and you will probably see hose clamps for the filler neck, after all things are unhooked the gas tank should come out, if you came this far you will probably be able to figure out how to remove the fuel pump, usually i will use a screwdriver and a hammer to turn the retaining ring or clip holding the pump in the tank..

Posted on Mar 12, 2010

  • 79 Answers

SOURCE: power door locks on 2005 chrysler town and

There is an ecu flash for this repair. You may get the locks to start working again with a battery disconnect.

Posted on Jun 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Van will not fire turn key off and on several times and it starts


Use a gage and check proper fuel pressure. Cycling the key on and off several times before you crank it, allows the fuel pump to prime the system.
How long since a tune-up? Are there any applicable trouble codes?

Jun 09, 2016 | 2000 Chrysler Town & Country

1 Answer

1998 chrysler town and country no crank no spark no injector pulse


I'm assuming you already checked: 1. Battery voltage at the terminals 2. Battery cable connections 3. Voltage to the starter at the starter 4. Jump the starter 5. Voltage to the switch 6. Test the switch?

Jun 05, 2014 | 1998 Chrysler Town & Country

1 Answer

Won't turn on


CRANKING IS GOOD BATTERY/STARTER. CHECK FOR SPARK. THEN FUEL, PUMP TO INJECTORS, THERE IS A FUEL PUMP RELAY

Mar 02, 2014 | 2001 Chrysler Town & Country

1 Answer

Car wont start i can hear the fuel pump and it has fuel No problems untill now When i turn the start key i can hear the fuel pump cycle motor turns over fine good battery


Is it clicking or is the engine actually turning over?

The starter solenoid contacts can become worn and need replaced. It's built onto the starter.

You need to check for spark at a plug wire... I have read the coil packs can become brittle and crack easily.

Jan 18, 2011 | 2001 Chrysler Town & Country

1 Answer

97 chrysler town & country dies while driving will only start when in park, runs fine but dies without warning and will restart in park???


Well first it should only restart in park or nuetral, any check engine light on? May be fuel pump if not. Listen for pump running in fuel tank. Should run at key on for a few seconds. If check engine light on, it should be scanned for codes, possible crank sensor

Aug 10, 2010 | 1997 Chrysler Town & Country

1 Answer

2005 chrysler Town&Country clicks when attempting to start


If the click is one click then that points to the starter. Make sure the battery connections are tight. If it clicks like a machine gun then it is either the battery or a bad connection. Good battery voltage is 12.6 or more and 13.6 when running. I don't know tour skill level of electricity.

Sep 25, 2009 | 2005 Chrysler Town & Country

1 Answer

Describe your 2002 Chrysler Town &


Safety neutral switch o.k.? Tried moving shifter through all gears while holding key in start position?

Aug 03, 2009 | 2002 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...