Question about Cars & Trucks

Open Question

How to remove the weight from clark it40 lift truck

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 olds aurora 3.5l engine removal


Remove the bonnet, drain oil and water remove radiator and fan remove all hoses cables and wiring attached to the engine. take weight of engine with a floor crane support the transmission .uncouple transmission from engine remove engine mount bolts , take a little more weight with the crane and slide engine clear of transmission , lift clear of car and slide crane clear to engine stand.

Dec 25, 2014 | 2001 Oldsmobile Aurora

1 Answer

Lifting a engine out of a 256c cat skidloader


check around the rear section and see if there is a way of removing the door/weights. Use a lift bar on another fork lift and chain the motor to that bar . Undo all the bell housing bolts and engine mounts and lift a bit and back the fork lift to get the motor out.

Jun 24, 2014 | Cars & Trucks

1 Answer

Toyota forklift


use a crane to take the weight . Undo the long mounting bolts that go through the weight .Ensure that you have sufficient lift on the crane or the weight will fall and hurt you.

Feb 21, 2014 | Cars & Trucks

1 Answer

Do it yourself 1995 ford windstar r/f motor mount install


you need to support engine weight using lift or chain hoist.you have to slightlty raise engine to take weight off engine mount before removing engine mount.

Apr 04, 2013 | Cars & Trucks

1 Answer

Where is the oil pump


its in the oil pan, I just removed mine. If you have a 4X4 you have to remove the skid plate, then the front axle assembly, use an engine hoist to lift the motor slightly to get the weight off the motor mounting brackets, remove them, then you can get to the oil pan. Its not extremely difficult, I managed to do it without a motor lift, but I definitely recommend using one.

Mar 12, 2012 | 1997 Dodge Dakota

1 Answer

I need to replace a rear air suspension bag. What are the procedures and how hard is it to do.


If the defective air bag is already deflated, half your hard work is done. Replacing them is as simple as lifting the vehicle so that the weight is off that airbag. disconnect sir line, remove clip at the top and slide out. Installation is reverse of removal. It is also a good idea to disconnect battery before starting so that the airbag module will self-reset. If the vehicle has a shock absorber as well. disconnect it from the bottom prior to lifting the truck.

Sep 12, 2011 | 2000 Ford Expedition

1 Answer

Change out bad motor mounts


YOU HAVE TO SUPPORT ENGINE WITH A LIFT TO TAKE ENGINE WEIGHT OFF THE ENGINE MOUNTS.THE HOOD MORE LIKELY HAVE TO REMOVED YOU NEED A HELPER TO REMOVE HOOD AND MARK HOOD HINGES SO YOU CAN REINSTALL HOOD HINGES IN THE ORIGINAL POSITION. IF YOU CAN POSITION ENGINE LIFT IN POSITION WITH OUT DAMAGING THE HOOD.THE DONT HAVE TO BE REMOVED THATS YOUR OPTION IF HOOD IS IN THE WAY.

Feb 21, 2011 | 1998 Volvo S70

1 Answer

How do i remove the gas tank from my 1999 chevrolet trail blazer


Depending on how rusted your Blazer is. You either remove the bolts from the straps or cut the straps off and replace both. Get a 2x4 and place of lift jack. The tanks should be about empty or a pain to lift. Lift the jack up to take some of the weight off the tank. Try to unbolt straps. If no luck. Get out a hand power grinder. Start cutting. That's about the only way I know. We removed my son's fuel tank off a 1988 GMC pickup last Sunday. Everything was rusted BAD The straps had to be cut. We didn't have any replacements. So we used 3 ATV orange racket straps. Worked fine so far.

Jun 05, 2010 | 1999 Chevrolet Blazer

1 Answer

How do I replace the motor mounts on my 96 thunderbird 3.8L?


Put the car on ramps and set e brake.

Use engine hoist to lift engine weight off of car.

Remove mount to engine bolts, remove mount nut.

Lift engine just enough to remove mounts and install new.

Watch exhaust, fuel lines and transmission mount while lifting. They may have to be loosened or moved.

May 21, 2010 | 1996 Ford Thunderbird LX

2 Answers

Rear leaf springs


if its not jam in rust it easy disconnect the shocks lift remove the ubolt anf lift the truck untill spring loose remove bolt front and back that about it i guest the worst its lifting the truck high be carefull safety first hope it help fixya our post thanks pierre

Jul 18, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...