Question about Cars & Trucks

Open Question

2014 F150 front bumper exploded view

Front brackets that holds bumper on

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
oilyspill
  • 3491 Answers

SOURCE: exploded view with part numbers of 2014 F150 front bumper

I just posted the picture as an example, I believe that picture is for Harley Davidson version, 014-- f150.
Go to fordparts.com
Click the model link so you can type in year--make--model. When the page comes up, in the key-work box, type in front bumper, pick the one you want to look at. then in the right column has call-out numbers matching the numbers in the picture. That is all the help I have, at the moment. Hope you get it going your way.
front bumper-kuq1mw3hokvd33y4votkkw1u-5-0.jpg

Posted on Apr 21, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Exploded view with part numbers of 2014 F150 front bumper


I just posted the picture as an example, I believe that picture is for Harley Davidson version, 014-- f150.
Go to fordparts.com
Click the model link so you can type in year--make--model. When the page comes up, in the key-work box, type in front bumper, pick the one you want to look at. then in the right column has call-out numbers matching the numbers in the picture. That is all the help I have, at the moment. Hope you get it going your way.
front bumper-kuq1mw3hokvd33y4votkkw1u-5-0.jpg

Apr 21, 2017 | Cars & Trucks

1 Answer

How do I go about installing a Warn winch on the metal bumper and chassis of a 1996 3.0l v6 Mitsubishi Pajero without modifications? Cables are standard Warn designed for this winch.


just make sure you get the right steel plate for your bumper to hold the winch on or it will rip your bumper off the first time you use it make sure it is bolted sucure

Jan 19, 2015 | Mitsubishi Cars & Trucks

1 Answer

Exploded view of 1952 Chevy front end area


Sorry we do not have any diagrams available to us for that far back. Below is a picture of a stock front end

9_4_2012_6_51_07_pm.jpg

Sep 04, 2012 | Chevrolet DELUXE Cars & Trucks

1 Answer

How to get the half shaft out


Halfshaft -sorry but the diagrams didn't paste into the fixya.com window, just the text. Also, this was for a 3.2L engine.
REMOVAL & INSTALLATION

  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Negative battery cable
    • Front wheel
    • Radiator skid plate
    • Transfer case skid plate
    • Brake calipers and mounting bracket
    • Brake rotor
    • Wheel speed sensor
    • Steering knuckle

  3. Support the axle housing with a jack. Unbolt the axle mounting bracket and
    remove the halfshaft/bracket assembly.
    To install:

  4. Install or connect the following:

    • Axle/bracket assembly. Tighten the bracket flange bolts to 85 ft. lbs. (116
      Nm) and the bracket mounting bolts to 112 ft. lbs. (152 Nm).
    • Steering knuckle
    • Wheel speed sensor
    • Brake rotor
    • Brake caliper and mounting bracket. Tighten the bracket bolts to 115 ft.
      lbs. (155 Nm).
    • Transfer case skid plate. Tighten the bolts to 27 ft. lbs. (37 Nm).
    • Radiator skid plate. Tighten the bolts to 58 ft. lbs. (78 Nm).
    • Front wheel
    • Negative battery cable

  5. Check the wheel alignment and adjust as necessary.





    Fig. 1: Exploded view of the left halfshaft, axle shaft and
    axle disconnect
    7924bg26.gif






    Fig. 2: Exploded view of the right halfshaft and mounting
    bracket
    9308bg03.gif



prev.gif next.gif

Oct 31, 2010 | 2002 Isuzu Rodeo Sport

1 Answer

Where is located the ford f-150 horn


If you slide under the front bumper, in front of the passenger side front wheel, and look up, the high and low note horns should be on a bracket right there.

9f6a205.jpg

Nov 27, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

2 coils located behind front bumper one exploded causing fire


FIRE???? I would have the dealer look at it ASAP.

Sep 28, 2009 | 2003 Volkswagen Eurovan

1 Answer

How do i remove front bumper on 95 aerostar?


The bumper itself is a metal bar beneath the cover. You will have to access the underneath of the vehicle and remove the bolts holding the bracket for the bumper. Depending on the model make sure any light are disconnected first. Once the bumper is off you can remove the bumper cover and replace new bumper support

Jul 15, 2009 | 1995 Ford Aerostar

1 Answer

How can I change the headlights in a 1998 Honda Accord?


Its not that hard but you have to remove bumper to get to the two bottom bolts that holds the headlights. First remove grille and there are 2 10mm bolts that holt the tip of fenders they are the first bolts under the fender weld closes to the bumper cover. Then there are two bumper mounts/brackets that hold bumper to frame/radiator support. they are held by (4) 12mm bolts may need a swivel socket to get to them( easily accessed if you remove front signal lights in the bumper held by philips screws in the corners).After removing bracket bumper should come right off. Headlights are in plain clear view. (4) 10mm bolts and you are done. Re-install in the reverse. Good Luck . If I fixed ya leave me a FIX-YA comment. Contact me if you need more info

Dec 10, 2008 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...