Question about Lincoln Cars & Trucks

Open Question

How do I replace reverse lights on a 1998 lincoln navigator

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Need help w/1998 Navigator

Coil Pack or coil packs are bad there is 1 for each spark plug

Posted on Sep 08, 2008

chuck943
  • 783 Answers

SOURCE: where are the plugs on lincoln navigator 1998

They are under the coil packs. You will need an 8mm socket to remove the bolt on each coil pack then remove them to access spark plugs.

Posted on Feb 25, 2009

  • 9 Answers

SOURCE: 1998 lincoln navigator won't start

disconnect the battery wait a min then try it this should reset the car.if that's not it let me know what the car is doing when you turn the key example lights dim no sound ,lights don't dim no sound if their is a sound what kind 

Posted on Aug 22, 2009

  • 1986 Answers

SOURCE: replace rear brake light bulb 1998 lincoln continental

pop the trunk and right behind where the lights are pull the carpet down and their will be of the following depending on the trim.

You will either see the light sockets themselves that you can twist and pull to change the bulb, or you will see the plastic nuts/screws that you can remove to remove the entire assembly in order to access the bulbs.

If it's your 3rd brake light, the screws to access the housing are located in the upper part of the trunk

Posted on Oct 26, 2009

c17hydro
  • 2984 Answers

SOURCE: The heater core is shot on my 1998 lincoln

The heater core costs about $42.00 at several parts stores....the labor? Well...very good guess is $89.00 per hour to start and depending on what garage you go to...$90 and up.

I could email you the steps to do the job yourself, but I can tell you it is a REAL pain...the entire dash must come off...

Here is a little bit of the steps just to give you and idea:

  1. Disconnect the battery ground cable.
  2. Drain and recycle the engine coolant.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

  1. Remove the instrument panel. Refer to Section 10.
  2. If equipped with the 5.4L 4V engine, remove the junction block splash shield.
  3. If equipped with the 5.4L 4V engine, remove the bolts and disconnect the cable ends from the starter relay.
  4. If equipped with the 5.4L 4V engine, remove the junction block bracket.
  5. Disconnect the heater core hose couplings.
  6. Remove the retaining screw and remove the A/C plenum demister adapter.
  7. Disconnect the vacuum line from the A/C plenum demister adapter.
  8. Remove the heater core bracket.
  9. Remove the 13 plenum chamber top retaining screws.
  10. Remove the plenum chamber top.
  11. Remove the blend door assembly from the case.
  12. Remove the heater core.
    To install:
  13. The installation is the reverse of the removal.
The above is to JUST remove the heater core....this part of how to GET to the heater core:

  • If equipped, remove the floor console assembly.
  • Remove the lower steering column cover bolts and the cover.
  • Remove both front door scuff plates.
  • Remove both side cowl trim panels.
  • Disconnect the electrical connector from the Brake Pedal Position (BPP) switch.
  • Remove the radio ground and the GEM/CTM ground bolts.
  • Disconnect the left side instrument panel main wiring harness connector.
  • In the engine compartment, remove the bulkhead wiring harness connector bolts and disconnect the wiring connectors.
  • In the driver’s compartment, release the 6 locking tabs and remove the bulkhead electrical connector from the instrument panel.
  • Disconnect the air bag diagnostic monitor electrical connector.
  • Disconnect the inertia fuel shutoff switch electrical connector.
  • Remove the right side ground bolts.
  • Disconnect the right side instrument panel wiring harness connectors.
  • Disconnect the electronic blend door actuator electrical connector.
  • Disconnect the climate control head vacuum harness connector.
  • Remove the steering column opening cover reinforcement nuts and the cover reinforcement.
  • At the base of the steering column, disconnect the air bag sliding contact and the anti-theft sensor electrical connectors.
  • At the steering column, disconnect the remaining electrical connectors.
  • If equipped with a transmission range indicator, remove the bolt and disconnect the cable.
  • Remove the steering column-to-instrument panel nuts and lower the steering column.
  • Remove the right side front fender splash shield screws and move the shield away from the panel.
  • Disconnect the antenna cable from the antenna base.
  • Remove the instrument panel relay cover and disconnect the autolamp sensor electrical connector and/or the sunload sensor connector.
  • Remove the glove box.
  • At the passenger’s air bag module, remove the screws, disconnect the electrical connector and remove the air bag module.
Place the air bag module in a safe place with the front facing upward.
  • Remove the right side assist handle screw covers, the screws and the handle.
  • At both doors, pull back the weatherstrip seals and remove the windshield garnish moldings.
  • Remove the instrument panel reinforcement bolt below the left side corner of the glove box.
  • Through the air bag module opening, remove the instrument panel bolts.
  • On Expedition, remove the upper instrument panel cowl covers and bolts.
  • On Navigator, remove the instrument panel defroster grille assembly and the instrument panel cowl top bolts.
  • At the relay bracket, remove the instrument panel bolt.
  • At the lower left side of the cigar lighter, remove the instrument panel bolt.
  • At the both sides, remove the instrument panel-to-cowl side nuts.
  • At the steering column opening, remove the instrument panel bolts.
  • Remove the upper instrument panel floor brace bolt.
  • Using an assistant, remove the instrument panel.
  1. If equipped with the 5.4L 4V engine, remove the junction block splash shield.
  2. If equipped with the 5.4L 4V engine, remove the bolts and disconnect the cable ends from the starter relay.
  3. If equipped with the 5.4L 4V engine, remove the junction block bracket.
  4. Compress the holding tabs and disconnect the heater hoses from the heater core.
  5. Remove the air conditioning plenum screw and the air conditioning plenum demister adapter.
  6. Disconnect the vacuum line.
  7. Remove the heater core bracket screws and the bracket.
  8. Remove the 13 heater housing plenum camber cover screws and the heater housing plenum chamber cover.
  9. Remove the blend door assembly from the heater housing.
  10. Remove the heater core.

Posted on Dec 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finding reverse lights fuse for 1998 lincoln navigator


It's 15A fuse 5 in the junction box fuse/relay panel.

Sep 04, 2016 | 1998 Lincoln Navigator

1 Answer

How to open 1998 Lincoln Navigator it latch is broken?


Help:Navigator hood won't open - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > Expedition & Navigator
Jan 30, 2012 - I have a 1998 Lincoln Navigator with a battery that needs to be jumped and I cannot .... I've accessed many broken hood latch cables that way. Rear liftgate and glass latch cables -1998 Expedition
Jun 1, 2012
Expedition hatch door doesn't open
Jun 20, 2011
need help replacing door lock actuator....98 Navigator
Jan 28, 2008
More results from www.ford-trucks.com

Sep 28, 2015 | 1998 Lincoln Navigator

1 Answer

Blinking light on 4 all wheel drive at 98 Lincoln navigator


i have a 1998 lincoln navigator,my problem,when i turn on the a.w.d all weel drive,the front weels does not pull,onley the back

Dec 13, 2010 | 1998 Lincoln Navigator

1 Answer

Replace reverse lights on 1998 lincoln continental and brake lights


reverse lights_ have a screw behind plate remove screws and pop out assembly..
third brake light_remove liner in trunk and bulbs pop right out
brake lights have to be complete;y diassembled from inside trunk

Jul 23, 2009 | 1998 Lincoln Continental

1 Answer

Need help w/1998 Navigator


Coil Pack or coil packs are bad there is 1 for each spark plug

Jun 17, 2008 | 1998 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...