Question about Plymouth Reliant

1 Answer

No reverse lights, changed the nuetral saftey swicth already, bulbs good, socket good, has power to sockets

Posted by on

  • lobiscardi Jul 24, 2009

    thank you will check that out.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

There is most likely a bad ground to the socket or from ground wire socket to grounding post or frame, check the continuity through ground wire by setting the voltmeter to ohm or the symbol icon that looks like a bell then touch the positive probe to the ground wire and the negative to a suitable ground like a nut or bolt head somewhere, the meter should read almost zero if it reads above 1 or 2 or if it is up to 5 the ground wiring needs to be repaired. .023-.06 is ok.

Posted on Jul 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Reverse light not working what to do

If bulbs are good then you need to check the switch that powers them when you put the car into reverse.

FYI - Neutral safety switch prevents car from starting unless it is in neutral transmission position only.

Oct 05, 2015 | Cars & Trucks

1 Answer

1987 dodge dakota 4x4 reverse lights do not work, wiring seems fine. Thinking a switch or relay prob. if so, where is it located. Help?

if it is a manual then it would be your reverse light switch, if it's auto then your neautal switch is worn seeing that you have check bulbs and wires already

Feb 16, 2014 | 1987 Dodge Dakota

1 Answer

Getting the brake light off to change light bulb

Most brake light bulbs are accessed from trunk interior. open trunk and look for removeable panels that might have 'click' catches. These panels will be adjacent to the bulb location. Once bulb socket is exposed, find the appropriate bulb and twist the socket counterclockwise about 1/4 turn and bulb socket should pull free out to expose bare bulb. Bulb should also either pull straight from socket or twist 1/4 turn and pull free from socket. Replacement is simply the reverse,

Oct 09, 2013 | 2005 Peugeot 307 SW

1 Answer

Saab reverse lights not working

Probley loose connection in bulb socket or loose wiring if that looks good check neutral saftey switch for auto trans and sensor for maunual trans which shoukd be mounted on the transmission housing look for corrosion and burnt wires for the reeverse circuit

Jun 11, 2013 | Cars & Trucks

1 Answer

Reverse lights will not come on on a 1996 dodge grand caravan/i already changed the bulbs and checked fuse

Did you use a Volt meter at the sockets to make sure you have power? If no power then you'll need to trace the wiring back from the reverse lights and find the broken or corroded connection.

Jan 16, 2013 | 1996 Dodge Caravan

1 Answer

I don't have any reverse lights on my 2000 toyota avalon

if the bulbs are good, then check the signal from the transmission range can check that at the bulb socket with the park brake set, the key on/engine off and put trans in reverse. use a test light and check power in the light socket. no power indicates bad fuse, bad wiring, or bad range switch.

Jun 14, 2012 | Toyota Avalon Cars & Trucks

2 Answers

Back up lights dont work, check fuse, bulbs and replace nutrue safty switch. stiil dont work.

check circuit board at lights and grounds, it is best to use a Power Probe to test as you can apply power or ground at the lights to verify problem.

May 03, 2011 | 1997 Dodge Caravan

1 Answer

I have a 2002 ford explore , the revese lights will not go on when in revese gear ??? have changed neutral saftey switch,cheched bulbs wiring,sockets.

When a driver engages the reverse gear he or she automatically switches the reverse light on by triggering the switch on and if the lights are not coming on it means that a number of reasons are to blame. I will start with fuses and the wiring around the switch. Thank you for using fixya!

Mar 09, 2011 | 2002 Ford Explorer

1 Answer

Lights prob

the sockets should ONLY have power when in reverse. if they have power when not in reverse, you have a bad wire connection somewhere. the cheapest way to go is to buy brand new bulbs if you haven't already. they are only about $2.

Nov 27, 2008 | 1994 Oldsmobile Cutlass

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides