Question about Jeep Cars & Trucks

Open Question

I need to know the 1990 Jeep fog lights diagrams

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

brainyass
  • 242 Answers

SOURCE: 1996 jeep cherokee sport.

If it's a lighted switch, you should have 3 terminal connections on it. One for the "ignition on" wire (from your fuse box). One going to the fog lights to turn them on when you flip the switch and one ground for the switch light to work. If your switch doesn't light, you should only have 2 terminal connections (no ground).

Find an "ignition on" plug on your fuse panel. It is only hot when you turn your ignition to the on position (not crank position). With your keys out, it should not have any power to it. Hook your "hot" wire from fuse panel to switch, take your keys out of the ignition first to be safe. Now hook the other wire from the switch to the "hot" on your fog lights. You will have to find a pass through rubber grommet on your firewall to go through. Use a clothes hanger to help fish it through. Now ground your fog lights to a grounding screw somewhere in the engine bay. There should be a few you can use, possibly one of the bolts that hold the front shroud on. Make sure it's a metal surface and use sandpaper to scrape off paint to get a metal to metal contact. Cover area with petrolium jelly to ward off rust. If your switch is lighted, hook to ground wire on fuse panel. Test with ignition on. If it doesn't come on, check your grounds again.

Posted on Oct 16, 2008

  • 6982 Answers

SOURCE: missing factory throttle linkages on 1990 YJ jeep. Need Diagram

Go to any scrapyard and you can get the entire setup for next to nothing...and you can see how it's hooked up!!!

Posted on Jul 07, 2009

ZJLimited
  • 17970 Answers

SOURCE: need a fuse box diagram to wire in fog lights

Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Posted on Aug 11, 2009

  • 14 Answers

SOURCE: fog lights don't work

In my 99 Cherokee it was the switch itself. Bought one online for about 20 bucks and it took about 5 minutes to replace.

Posted on Aug 20, 2009

  • 10 Answers

SOURCE: How to replace fog light bulb on an '03 Jeep

There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse diagram for 2002 jeep ,,fog lights don't work ,, bulb or fuse please help


google 2002 jeep {wrangler, renegade, whatever you have) wiring diagram
when page comes up at the top go across and click on images
you will see wiring diagrams
click on yours and click on visit siter
there you have it, mike

Mar 10, 2016 | Jeep Grand Cherokee Cars & Trucks

1 Answer

WIRING DIAGRAM FOR FOG LIGHTS


stock?

TJ jeep that is what it is
and ive posted the answer here 100s of times now.
here goes again
front FOGS
chapter 8L covers this, (8 is wiring, L means lighting)
so ?
see TJ 2003 , same here.
see chapter LAMPS.
then wiring chapter.
schematic is 8W-50 fogs.
wiring + front, (index)


http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service
its all there,

8W-50 (page 3,8,9 and 10)
if in usa, ignore EXPORT pages.... nobody here ever states there country , so..............................................mostly wrong answers.

Sep 07, 2015 | 2004 Jeep Wrangler

1 Answer

Need diagram of where to reach up to replace fog light 2011 grand Cherokee


lay under the front of your jeep with your head in front of the front wheel looking up towards the front of the car -you should be looking right at the back of the fog lamp-twist it--one way it won't move the other way it will come out-reverse to install new bulb-Denny

Nov 02, 2013 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Do you know how to run new vacum hoses on 1990 jeep cherokee laredo


there should be a vacuum diagram sticker under the hood to show you where hoses go if not let me know what engine and will see if i have a diagram

Sep 25, 2011 | 1990 Jeep Cherokee Limited

1 Answer

How to replace fog light bulb on an '03 Jeep


There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Feb 11, 2010 | 2003 Jeep Wrangler

2 Answers

I want to install aux. backup lights and not wiring them to the jeeps backup ligts. I don't understand the switch. It has three prongs on the back The diagram shows one is power coming from the relay one...


What diagram? What switch? Are you using a switch that salready in the Jeep, or a switch that you bought? You really need a relay to handle th ecurrent of the lights. The relay will have 4 terminals, The relay is really just a remote switch. Let the relay take the power, not the switch. Buy a relay for fog lights and it should have a diagram you can use.

Dec 19, 2009 | 2004 Jeep Wrangler

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Have a mazda eunos year 1990. switch for fog light lights up when switched on ...cant find fog light on rear? which bulb is for fog light please!


Many MX5 owners convert the extra brake light on the boot lid to a fog light. Has this been done to yours?

Jun 15, 2009 | 1990 Mazda MX-5

1 Answer

Need fog light installation instructions


Stop by your local Jeep dealership and ask teh service tech to go over the schematic and wiring diagram with you.
Most Jeep service depts. are quite helpful and won't charge you for knowledge.
Then head over to NAPA and get the parts for cheap.
If you are restoring to factory specs for show car purposes, you should get the MOPAR parts right from the dealer.
Most of the time the Jeep Wranglers have the wiring already in place, you just have to know where to look for the unused plug. At least that's how it is with my 2007 JKL Rubicon.

May 13, 2009 | 1999 Jeep Wrangler

1 Answer

Fog lights don't work


In my 99 Cherokee it was the switch itself. Bought one online for about 20 bucks and it took about 5 minutes to replace.

May 02, 2009 | Jeep Wrangler Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...