Question about Oldsmobile Cars & Trucks

1 Answer

Where is the crankshaft sensor on 01 ALERO oldsmobile

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Oldsmobile Master
  • 923 Answers

The crank sensor is located beneath the intake between the starter and oil filter it has one small bolt in it remove the bolt and pull the sensor out.

Posted on Apr 21, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: crankshaft position sensor

Here you go:
Fig. 3: Crankshaft position sensor (1) is located next to the oil filter (2) on the 2.4L engine
7cf6b9b.jpg

Posted on Aug 29, 2008

alicantecoli
  • 22246 Answers

SOURCE: 2000 alero crankshaft position sensor

yes it can stop vehicle from starting,but i would call a mobile mechanic to check it out for you,start changing bits willy nilly and it will cost you more in the long run.

Posted on Jan 23, 2009

dealt_soul
  • 296 Answers

SOURCE: MAP sensor

Located on the MASS air flow attatched to the air box

Posted on Feb 16, 2009

  • 840 Answers

SOURCE: 1999 Olds Alero 3400 motor -- location of Crankshaft sensor

Welcome to fixya. If you need anything else go to www.collisionrepairadvice.com here is the location.
On the lower rear of the engine (LA1) for the 7x
and for the 24x

On the lower rear of the engine (LA1

Posted on Jul 26, 2009

Testimonial: "Got it Thank You!!! Actually my problem was a bad fuel pump in the gas tank."

emissionwiz
  • 76846 Answers

SOURCE: crankshaft sensor location on 2001 oldsmobile

. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wIre CONNECTOR plug to the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor for a oldsmobile silhouette 01


I have enclosed a picture diagram to help you locate the crankshaft sensor, some have two sensors so you will need to look. the first location is behind the crankshaft harmonic pulley. and the other location is on the right side of the engine. hope this is helpful.11_14_2011_5_55_55_pm.gif

Nov 08, 2011 | 2001 Oldsmobile Silhouette

1 Answer

How to put on a crank sensor for a 2.4 engine of a 2001 oldsmobile alero?


The crankshaft position sensor on your vehicle goes through the engine block and is held by a single mounting bolt.
Disconnect the electrical connector.
Remove the mounting bolt securing the sensor to the engine block.
Using a "twisting back and forth" motion, remove the sensor from the engine block.
NOTE: it is common for these to be coated with carbon deposits that may cause them to stick and make them difficult to remove. Be careful to pull STRAIGHT out and use the twisting motion mentioned above, to avoid breaking the sensor off inside the engine block.
The crankshaft position sensor is located on the left side of the engine block near the oil filter.

Oct 23, 2011 | 2001 Oldsmobile Alero

1 Answer

Where is the crank shaft sensor located on a 2001 oldsmobile alero


on the 3.4 liter engine, it's behind the harmonic balancer--you have to remove the crankshaft pulley/balancer to see it.

if you have the 2.4 liter, it's just above the oil filter:

jturcotte_156.gif

Nov 13, 2010 | 2001 Oldsmobile Alero

1 Answer

Where is the crank shaft sensor located on my 2000 alero?


ABOVE THE OIL FILTER ON THE 2.4 ENGINE AND THE 3.1 AND 3.4 ENGINE CRANKSHAFT SENSOR LOCATED BEHIND CRANKSHAFT PULLEY.

May 10, 2010 | 1999 Oldsmobile Alero

1 Answer

Where is the crank shaft sensor located on my 2000 alero?


CRANK SHAFT SENSOR FOR A 2.4 ENGINE NEXT TO OIL FILTER.FOR THE 3.1 - 3.4 ENGINES CRANK SHAFT SENSOR LOCATED BEHIND CRANKSHAFT PULLEY.

Mar 18, 2010 | 1999 Oldsmobile Alero

1 Answer

1999 Olds Alero 3400 motor -- location of Crankshaft sensor


Welcome to fixya. If you need anything else go to www.collisionrepairadvice.com here is the location.
On the lower rear of the engine (LA1) for the 7x
and for the 24x

On the lower rear of the engine (LA1

Jul 26, 2009 | 1999 Oldsmobile Alero

2 Answers

2000 alero crankshaft position sensor


yes it can stop vehicle from starting,but i would call a mobile mechanic to check it out for you,start changing bits willy nilly and it will cost you more in the long run.

Jan 23, 2009 | 2003 Oldsmobile Alero

2 Answers

1999 Alero stalling issue


check your throttle position sensor

Sep 27, 2008 | 1999 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...