Question about Cars & Trucks

Open Question

I have a 2009 town and country lx with 2 working fobik keys and want to add a 3rd key but it will not enter programming mode the way it should with the 2 working fobik keys.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75817 Answers

SOURCE: program a transponder key

this must be done by the dealer.

Posted on Mar 24, 2009

baccardo
  • 150 Answers

SOURCE: Programming a key fob

you will need the dealership diagnostic tool to program the remote

Posted on Apr 24, 2009

  • 109 Answers

SOURCE: HOW TO PROGRAM A FOBIK

your car came with 2 fobiks from the factory, if you bought a third one from Chrysler, read on, insert the first one in the win module, (key hole), and turn ignition to on only, watch your sentry red light to come on, wait till it goes out, you have ten seconds to insert the second one, red light will come on and start to blink, you have ten seconds to insert the third one , turn it to on and watch the red light to blink and once it stops and a chime will sound, the third fobik is now programed. If you only have one fobik, lost the other, your out of luck, you will have to visit a Chysler dealer. GOOD LUCK, RDJRP

Posted on Sep 05, 2009

  • 14036 Answers

SOURCE: re program my key fobik for a 2011 grand Cherokee jeep

put program key in ignition turn ignition switch to on position engine off for 3 to 15 seconds.you should hear acoustic signal and immobilizer lamp will flash then turn off ignition switch.you need two program keys to do this procedure twice. with in sixty second insert non program key in the ignition switch turn to on position engine off for at least with ten minutes you should hear acoustic noise immobilizer lamp flashing turn off ignition switch if all failed the dealership have to use diagnostic equipment to reprogram ignition key or keys.

Posted on Oct 26, 2012

alicantecoli
  • 22156 Answers

SOURCE: 2009 town & country lx will not start. radio, gauges, interior lights all work. wont turn over. no sound made at all.

Have you lost the chip out of the key?? try the spare key before you go any further

Posted on Mar 04, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CAN NOT PROGRAM NEW KEY FOR 2008 TOWN AND COUNTRY


RESET AND REPROGRAM ALL KEYS, CAN ONLY DO A SET NUMBER, I THINK 8 KEYS. START OVER CLEAN

Mar 12, 2014 | 2008 Chrysler Town & Country

1 Answer

My key/fob will open my car but it will not start not even a sound


It is most likely going to be a electrical problem on the printed board inside the key fobik. Take it to the dealership and see if they can try to re-program the key fobik and see if that works.

Sep 12, 2013 | 2005 Mercedes-Benz Mercedes Benz SLK350

1 Answer

Key stuck in ignition of 2009 chrysler town and country


Try to start it in neutral. If it starts then it sounds like a neutral safety switch. If the battery is dead it may not let the key out unless you jump the van.

Mar 01, 2013 | 2009 Chrysler Town and Country

1 Answer

Re program my key fobik for a 2011 grand Cherokee jeep


put program key in ignition turn ignition switch to on position engine off for 3 to 15 seconds.you should hear acoustic signal and immobilizer lamp will flash then turn off ignition switch.you need two program keys to do this procedure twice. with in sixty second insert non program key in the ignition switch turn to on position engine off for at least with ten minutes you should hear acoustic noise immobilizer lamp flashing turn off ignition switch if all failed the dealership have to use diagnostic equipment to reprogram ignition key or keys.

Oct 26, 2012 | 2011 Jeep Grand Cherokee

1 Answer

T & C 2001 REMOTE CONTROL PROGRAMMING


ATTENTION: You MUST HAVE one working remote to add one more to the system.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. A chime will sound afer each
additional remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.

Sep 17, 2012 | 2001 Chrysler Town & Country

1 Answer

Alarm button broken. Cannot disarm alarm. What do I do? Chrysler Town & Country LX 2003 model.


You can arm or disarm alarm manually with the key at the drivers side door, turn the key to open the locks and the alarm must be disarmed.

Nov 01, 2010 | 2003 Chrysler Town & Country

1 Answer

2003 Chrysler T&C Key programming


STANDARD PROCEDURE - TRANSPONDER PROGRAMMING USING A DRB III® SCAN TOOL All Sentry Keys included with the vehicle are pre-programmed to work with the Sentry Key Immobilizer System (SKIS) when it is shipped from the factory. The Sentry Key Immobilizer Module (SKIM) can be programmed to recognize up to a total of eight Sentry Keys. When programming a blank Sentry Key transponder, the key must first be cut to match the ignition lock cylinder of the vehicle for which it will be used. The vehicle's four digit PIN code will be required to complete this task since you will need it to enter the Secured Access Mode in the SKIM. The following steps must be completed using a DRB III® scan tool:
  1. Insert the blank key into the ignition and turn it to the RUN position.
  2. Using a DRB III® scan tool, select "Theft Alarm," "SKIM," "Miscellaneous," and then "Program New Key."
  3. Enter the four digit PIN code using the DRB III® scan tool. When programming is completed, the SKIM will exit Secured Access Mode and the DRB III® scan tool will display the results of your attempt to program the key. One of five distinct results may be displayed. All five are listed below:
    • "Programming Successful" is displayed if the Sentry Key programming is successful.
    • "Learned Key in Ignition" is displayed if the key in the ignition has already been programmed into that vehicle's SKIM.
    • "Eight Keys Already Learned (At The Maximum) Programming Not Done" is displayed if eight keys have already been programmed into the SKIM. In this case, if a new key needs to be added due to a lost or defective key, the "Erase All Keys" command (which requires entering the Secured Access Mode) has to be performed. Following the "Erase All Keys" command, all keys that will be used to operate the vehicle MUST be reprogrammed to the SKIM.
    • "Programming Not Attempted" is displayed after an "Erase All Keys" function is executed.
    • "Programming Key Failed" is displayed if further diagnosis is required.
To learn additional keys, turn the ignition OFF, remove the learned key, insert the next new blank key, and repeat the steps from the beginning.
“CUSTOMER LEARN” MODE This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a DRB III® scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
  1. Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes.
  2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position.
  3. After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key.
  4. About ten seconds after the completion of Step 3, the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode.
  5. Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position.
  6. About ten seconds after the completion of Step 5, a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKIS will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.
These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKIS will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKIS will also automatically exit the "Customer Learn" programming mode if:
  • It sees a non-blank Sentry Key when it should see a blank.
  • If it has already programmed eight (8) valid Sentry Keys.
  • If the ignition switch is turned to the OFF position for more than about fifty (50) seconds.
NOTE: If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE: Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.

Oct 15, 2009 | 2003 Chrysler Town & Country

1 Answer

HOW TO PROGRAM A FOBIK KEY FOR 2008 DODGE CHARGER


your car came with 2 fobiks from the factory, if you bought a third one from Chrysler, read on, insert the first one in the win module, (key hole), and turn ignition to on only, watch your sentry red light to come on, wait till it goes out, you have ten seconds to insert the second one, red light will come on and start to blink, you have ten seconds to insert the third one , turn it to on and watch the red light to blink and once it stops and a chime will sound, the third fobik is now programed. If you only have one fobik, lost the other, your out of luck, you will have to visit a Chysler dealer. GOOD LUCK, RDJRP

Jun 03, 2009 | 2005 Dodge Charger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...