Question about Cars & Trucks

Open Question

Reassembly of handle for model kfp07110b0 - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inside door handle will not release latch to open door. Must roll down window and unlatch from outside.


undo the door card after removing any parts that may need to be removed in order to release it. Remove the door card paying attention to the rod that should be attached to the internal door handle.. If there is no rod, it has become detached. You will have to check, in this case , why it has become detached. It may be that the end has deformed or that it has snapped, or something it should be attached to is snapped.
The mechanism may be jammed, in which case disassemly, correction, lubrication and reassembly may be necessary.
It should, hopefully, be a straightforward repair

Jun 28, 2015 | Cars & Trucks

2 Answers

How do I remove the door lock in a 1981 Datsun 280zx


Remove the interior door card is your first step.

Mar 03, 2015 | Datsun Cars & Trucks

1 Answer

Window off-track


dont recomend it the process is a big job. start with the mirror cover 2 window switch3 pull handle 4 about ten screws in trim panel and aem rest. then unbolt window from window regulator lift out of door enough to tilt window to alighn it to trackes. then reverse for reassembly

Dec 15, 2011 | 1989 Ford Mustang

1 Answer

How to remove the exterior door handle of a 2000 pontiac grandprix?


Hello,

To remove the exterior door handle of the 2000 pontiac grand prix, You will be needing these instruments, wrench set, Putty knife, Screwdrivers, Socket wrench set and please follow the steps below:
  1. Roll the door window all the way up. Disconnect the car battery's negative cable with a wrench.
  2. Remove all cover plugs on the interior door panel with a putty knife. Remove all armrests, door pulls, the window crank and trim-panel retaining screws with a screwdriver.
  3. Remove and disconnect any electrical devices in the door panel. Pry the controls out with a putty knife, and unplug the wires.
  4. Pry the trim-panel clips loose with the putty knife. Do not pry on the panel between the clips, or the panel could be damaged. Separate the trim panel from the door slightly, and disconnect the courtesy light. Remove the panel from the door, and peel back the plastic water shield.
  5. Detach the lock rods from the latch. Unhook the rods from the latch holes by hand.
  6. Remove the door-handle nuts with a socket wrench through the service holes in the door frame. Rotate the lock cylinder as needed for clearance, and pull the handle from the door.
  7. Reverse the steps for reassembly.
Hope this helped. Thank You for using FixYa!!!

Jan 14, 2011 | 2000 Pontiac Grand Prix

1 Answer

How do I remove the window winder mechanism on the drivers side door? The window is stuck partly open and I can't seem to move it. Peter


The fault is with the regulator on the window. Remove winder and door handles. Remove door lining and reconnect window to winder rail. Reverse for reassembly

Mar 17, 2010 | 1999 Daewoo Nubira

1 Answer

How do you properly remove inside panel on driver door of 2004 volvo xc 70 in order to access the window to put it back on its track?


Look for hidden screws, around the edge of the door, inside the door pocket, under the pull close handle and 'in & around' the door handle lever.
Then with those successfully removed, the whole door card should slide either up, or in the door edge direction to remove.
Be careful not to be too heavy handed, as this will undoubtedly break plastic lugs/clips etc.
Then once you have removed the door card, familiarize yourself, with where & how it fits on to the door for reassembly.
I hope I've helped.
Good luck

Jul 10, 2009 | 2004 Volvo XC70

1 Answer

Loose gearshift


INSPECTION 1. Inspect the bushing for wear or damage. 2. Inspect the return spring for damage or deterioration. REASSEMBLY 1. Apply multi-purpose grease to the sliding parts of the bushings. 2. Reassembly is reverse of disassembly. INSPECTION 1. Inspect the bushing for wear or damage. 2. Inspect the return spring for damage or deterioration. REASSEMBLY 1. Apply multi-purpose grease to the sliding parts of the bushings. 2. Reassembly is reverse of disassembly.8fa5804.jpg

Apr 24, 2009 | 2003 Hyundai Santa Fe

1 Answer

How to install exterior door handle on 95 Safari Van


hi, remove the entire door interior panel, keep notes and diagrams as you go, even take pics, usually the exterior handle is secured by 2 small screws or nuts, undo these and the handle will detach . there will be a small rod connected to this handle by a small clip or similar. reassembly is a reversal of the entire process, just take your time

Feb 11, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

I need to remove the drivers internal door panel


Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Feb 04, 2009 | 2001 Suzuki Swift

1 Answer

Nissan Sentra shifter lamp replacement


Transmission shift indicator light on center console.
First
make sure the fuse is good.
If the fuse is good then remove the screws holding the center console cover. You will need a long and short phillip screwdriver. Look for screws in the cup holder, under the handbrake handle and where the console runs under the dash. You may have to move seats forward/backward to reach the screws. When you attempt to raise the console cover you will notice you overlook a screws. Remove them also. You may be able to reach the bulb without removing the gear shift handle. DO NOT TOUCH any other electronics you see. The AIRBAG ACTUATOR is located here also. Replace bulb. Test before reassembly. Good Saturday morning project.

Nov 15, 2008 | 2001 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...