Question about Cars & Trucks

Open Question

What does it mean when it says, turn and fasten off?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are cylinder head torque specs?


Tighten the cylinder head bolts in the sequence shown in figure. Using the 4 step torque turn method, tighten according to the following values.
  1. Tighten center fasteners 1 thru 6 to 33 Nm (25 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  2. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  3. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs. ).



26083805-2jaahwjhyda0eguw15ciywpg-3-0.gif

Then tighten all fasteners 1 thru 10 90┬░turn . Do not use a torque wrench for this step.



26083805-2jaahwjhyda0eguw15ciywpg-3-2.gif

Feb 06, 2016 | 1999 Mitsubishi Eclipse

1 Answer

WHAT DOES IT MEAN, WHEN THE LIGHT CARRIER TURNS ON, TOO MY 1994 NISSAN PATHFINDER.


ok,if u have a tire carrier rack on the back to carry your spare tire on it means it is not fasten to the door that raises up to get in at the back.to get the light to go off u have to either take the fuse out of the fuse box or go to the back and unplug it from the sensor,so im assuming u dont have the rack on the back of the pathfinder.the light is to tell u if the spare tire rack is not fasten so it wont just swing out at any time.thanks

Feb 28, 2015 | 1994 Nissan Pathfinder

1 Answer

Door panel fasteners need to be replaced on 1999 Plymouth breeze


Where is it loose?
If you mean the plastic fasteners, like bullet clips, or rubber things that go around the bottom and up the sides, they fit into slots in the heavy cardboard backing of the panel. You slide the old one over a bit and free it and slide the new one in. If the bottom is floppy, loose, or the sides, you just need 2 or 3 inches clearance to put new fasteners in. If you can get a good look at one, you will see which way they slide or are pushed over to remove them. There's about 6 or 8 along the bottom, but 3 well placed ones would hold it tight. If you can't get to them, though, or if you mean another fastener (I think there's only rather small screws and those plastic pins.) then you will have to take the panel off. First remove all screws, some may be hidden behind a speaker screen or a little square trim piece. Then slip a blade or thin screwdriver under the panel to pry out the plastic pins. Start at the bottom and work up the sides. When all are popped out, the panel should be loose. Lift out and up to clear the panel out of the window channel`. Pull all the electrical connectors you need to to get the panel free.
Well, good luck. Hope I've helped you some.

Jul 21, 2012 | 1999 Plymouth Breeze

1 Answer

Where on the engine is the temp. sensor located on a Pontiac Sunfire 2003


The sensor is threaded into the pipe shown below. Please let us know if you have more questions.


2.2L Engine

NOTE Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  1. Turn OFF the ignition.
  2. Drain the coolant system.
  3. Disconnect the Engine Coolant Temperature (ECT) sensor electrical connector.
  4. Carefully back out the ECT sensor.

b08e1af.gif

Fig. Coolant temperature sensor for the 2.2L Engine




To install:

  1. Coat the threads only with sealer P/N 9985253 or an equivalent.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  2. Install the ECT sensor and tighten the ECT sensor to 18.5 ft. lbs. (25 Nm).
  3. Connect the ECT sensor electrical connector.
  4. Refill the engine coolant system.

Oct 28, 2010 | 2003 Pontiac Sunfire

1 Answer

Where does the motor ground cable fasten to the


You will have to be more specific, What is a Motor ground Cable...IF you mean an ENGINE Ground?? this can be bolted on anyplace that is not rusty or greasy of the said IRON Frame?? FYI: Motor is something that derives its power from an outside source, like a battery or electricity. an ENGINE is an Internal Combustion unit which makes its own power within itself, like a diesel which ignites the mixture by VERY high compression, a Gasoline ENGINE uses the same system only cannot build up as high a compression so it needs a spark from a plug to ignite the mixture which in turn blows the piston down its shaft, which turns the crankshaft, which turns the gears in the Transmission, which turns the wheels and THUS you have MOTION...try and do that with a MOTOR...HOWEVER they are attempting to invent exactly that with these electric vehicles, THEN and ONLY THEN can they be called MOTORS>..UR VELCUM

Jul 16, 2010 | 1997 Mercury Sable

2 Answers

Where is the battery located??


First, turn the steering wheel all the way to the right. From here you can remove the six screws holding in the battery access panel. Next, open the hood, unclip the air filter housing and remove the filter. It helps to get the cover up and out of the way by using a spare piece of wire and attaching it to the hood. Now, you're ready to remove the air filter housing. On the right side of the housing (facing the car) you'll notice a fastener with no apparent means of removal. This is a friction grommet, akin to the snaps on a baby's shirt. Grip the housing right above this fastener and give it a firm pull upwards. The housing should pop out over the fastener. The left side is not fastened - there are two "bumpers" that hold it in place on that side. Now you have complete access to the battery and can proceed with the replacement, sliding the battery out through the access door once it's been disconnected. Finally, it's much easier to re-install the battery access door from the top, before re-installing the air filter housing. It's possible, but not easy from down below. hope this helps,

Apr 16, 2010 | 2000 Chrysler LHS

1 Answer

Instructions to replace fuel composition sensor


  1. Turn OFF the ignition.
  2. Relieve the fuel pressure
  3. Remove the fuel composition sensor FCS attachment nut.
  4. Remove the 2 FCS attachment bolts.
  5. Remove the FCS from the frame rail.
  6. Disconnect the FCS inlet and outlet pipes from the FCS.
  7. Disconnect the FCS electrical connector.
Installation Procedure


  1. Connect the FCS inlet and outlet pipes to the FCS.
  2. Connect the FCS electrical connector.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the attaching nut.
  5. Tighten
    Tighten the nut to 17 N·m (12.5 lb ft)
  6. Install the 2 FCS attachment bolts.
  7. Tighten
    Tighten the bolts to 17 N·m (12.5 lb ft)

Jun 27, 2009 | 2005 Chevrolet Avalanche

1 Answer

"where is the Horn Location for 2001 Chevrolet Malibu"


Horn Replacement Removal Procedure
  1. Remove the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.
    794212.gif
    tif.gif
  2. Disconnect the horn electrical connector.
  3. Remove the horn bracket bolt.
  4. Remove the horn from the front frame rail.
Installation Procedure

    794212.gif
    tif.gif
  1. Position the horn to the front frame rail. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  2. Install the horn bracket bolt. Tighten
    Tighten the bolt to 10 N·m (89 lb in).
  3. Connect the horn electrical connector.
  4. Install the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.

May 17, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...