Question about Cars & Trucks

Open Question

My Tajma tmfxii 1506 1 of the heads just stopped working, the other 5 are still running fine

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tmfx 1506 One of my heads just stopped working, the other 5 heads are running fine. Need to fix


Wow! That simply "blows away" the saying, "two heads are better than one!"

Heads on what? Obviously not a living creature, unless it was a dragon in "How to Train Your Dragon!"

Maybe it's a radial aircraft engine from the 1920's. Those had a separate head for each cylinder. That was the type that had to be started by someone quickly pulling on the propeller. Is that what those six heads are on? How are the six spark plugs? Are any of them oil-fouled?

Apr 20, 2017 | Cars & Trucks

1 Answer

Replaced head gasket torqed everything to right spec started up and ran fine for 3 to 5 minutes made noise and died now cranks over fine no start


as the engine started and ran, indicates that the timing and chain sections were assembled right
the noise and stop never to start again may be attributed to cam or crank position senor problems
they both have a set clearance from the rotors to work properly so if one was not tension properly and touched a rotor it would make a noise and stop functioning
next is the lubrication of the cam shaft bearings
If the head gaskets were not installed the correct way up the oil passage may be blocked making the bearings run dry and seize up or spin in the bearing caps . Im a bit cautious on this as 3-5 minutes means for it to happen bearing caps would have to be misaligned , placing extra pressure on the shaft but it can happen quickly especially if the oil passage was blocked by the head gasket
in the event that that happened ti could have caused the timing chain to fail or jump timing
unfortunately I can only surmise and go on your insistence that it was done right but the sad fact is , something was done wrong , or it would still be going

Jan 08, 2017 | Cars & Trucks

1 Answer

Did valve and shave head job holds compression and seems to run fine but took a notion to smoke after warming up 99 volvo s 70 2.4 5 cylinder


did you blow a head gasket. i had a car in my garage that had a bad head gasket ,and when I replaced the head gasket the car smoked for 3 hours and then stopped

Feb 10, 2013 | Cars & Trucks

1 Answer

My 98 camry is idling rough at start up for 5 to 10 seconds.Then it runs fine,blowing a bit of white smoke but not much also loosing coolant out of the radiator no visible leaks.


You've got a blown head gasket, sounds small at this point, but it will get bigger. If you want to save this engine I would stop driving it.

Nov 20, 2010 | 1998 Toyota Camry

1 Answer

My car is mazda 626 1998 end he have enginer ligh on end code is 1506


The code 1506 is most likley the Bypass Air Control (BAC) Valve
Setting a 1506 code is for the dle air control out of range.
Dealer item only. Give dealer the vin # of the car and they will order it for you.

Sep 08, 2009 | 1998 Mazda 626

2 Answers

Right brake light does not work when running lights are on


sometimes a bad ground can cause this. when the other lights are not being used the brake light can backfeed through another bulb to get a ground.

Aug 02, 2009 | 2004 Jeep Grand Cherokee

1 Answer

1989 Honda Accord speedometer not working. What is a speedo head?


The speedo head or cluster is the part that houses the speedometer and tach, etc. now it may be the speedo cable that comes from the transmission to the speedo head that has broken. If so replace the cable and your back in business. If it is the head you can get them from your local recycle yard.

May 29, 2009 | 1989 Honda Accord 4 Door

1 Answer

Sputtering and hot


if it's running hot and really gutless it could be your timing..or a blown head gasket check your oil.make sure that it is not a milky color.if it is you probly have a blown head gasket..

Dec 03, 2008 | 2004 Honda Accord

2 Answers

Electrical / Lights / Gages


Pull instrument/ cluster panel and re-melt cold solder joints where circuit board connects to dash connectors. Get them hot enough to turn them bright silver, usually 3-5 seconds each pin.
Good Luck!

Jun 24, 2008 | 1996 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...