Question about Oldsmobile Cutlass

1 Answer

What bolts do I remove to drop caliper on a 1999 cutless olds

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 1,051 Answers

You need to remove the bolts at the top and bottom of the calipers. They normally require an allen wrench to remove. Hope this helps. In addition, you will need to compress the brake shoe to pull the caliper from the rotor. You can use a c clamp to push the cyl. back into the caliper.

Posted on Apr 20, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
heavymetal77
  • 721 Answers

SOURCE: where are the caliper bolts on a 1999 Dodge Dakota

They're on the top & bottom of the caliper. They should be 12 or 14 mm. Not the inner bolt that are about 19mm or bigger,those hold the entire bracket on.

Posted on Jun 27, 2009

underprivele
  • 22 Answers

SOURCE: removal of the caliper bolt of a 1995 nissan

you may need a star fitting to pull the bolt off and the rubber should just pull off

Posted on Oct 04, 2009

  • 43 Answers

SOURCE: how to remove front brake rotor on 1999 mitsubishi montero sport?

6290230.gif Here's an exploded view, you'll need to pop off the grease cap #6 then remove the snap ring #8 to get the hub off to get the rotor off. Hope it is of some help...pictures always are.

Posted on Dec 18, 2009

  • 280 Answers

SOURCE: how to remove the upper caliper bolt

I think you need a 3/8" allen wrench.

Posted on Mar 23, 2010

  • 1 Answer

SOURCE: 1999 ford Expedition caliper removal

IT IS RUSTED ON GO TO YOUTUBE AND SEARCH
"Remove Rusted Brake Rotors"

Posted on Jan 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 chevy lumina rear disc brakes. I thought a caliper bolt was broken. I went to the other side, it looks the same. so one is a bolt, what is the other thing? How does it come off?


you will remove the one bolt that holds the caliper to the bracket. Once that bolt is removed you can rotate the caliper away from the rotor and then slide it off the other caliper slide. Sometimes you will have to rotate it, remove the caliper bracket mounting bolts and then remove the caliper assembly due to the lack of clearance.

Sep 03, 2011 | 1999 Chevrolet Lumina

1 Answer

HOW TO FIX BRAKE PADS IN A 1999 CHEVY MALIBU?


Take off wheels, using a screwdriver pry between pad and rotor to push cylinder into caliper. Remove bolts holding caliper on rotor, remove old pad, replace with new pad, put caliper back on rotor. replace wheel, repeat other side. Als check rotor for wear, if bad get new rotors, always replace as a set

Sep 30, 2010 | 1999 Chevrolet Malibu

1 Answer

How do I remove the front brakes? Is there a special tool?


prev.gif next.gif Some GM Vehicles use aT-30 Torx bit, other use a regular hex head bolt with a ratchet tor remove the caliper. The following shows how to remove the caliper from the line. Brake Caliper Removal & Installation Front To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
  3. Raise and support the vehicle.
  4. Remove the tire and wheel assembly.
  5. Hand tighten 2 wheel lug nuts to retain the rotor to the hub.
  6. Install a large C-clamp over the brake caliper with the ends of the clamp against the rear of the caliper body and the outer brake pad.
  7. Tighten the C-clamp until the caliper piston is compressed into the bore enough to allow the piston to slide past the rotor and remove the C-clamp.
  8. Disconnect the brake line from the caliper and discard the two copper gaskets.
  9. Plug the brake line and the opening in the brake caliper. NOTE: On second design hardware, the upper caliper pin bolt has a bushing as part of the bolt. The lower caliper pin bolt is of a solid design.
  10. Remove the caliper pin bolts and the caliper from the bracket.
To Install:
  1. Replace any damaged caliper pin boots.
  2. If reusing the brake caliper pin bolts, wipe the old grease from the brake caliper pin bolts.
  3. On first design hardware apply high temperature silicone brake lubricant to the brake caliper pin bolts. On second design hardware, apply a thin coat of NIGLUBE® or equivalent grease to the brake caliper pin bolts. In either case it is not necessary to apply lubricant to the threads of the pin bolts.
  4. Install the brake caliper over the brake pads into the brake caliper bracket. NOTE: On second design hardware, the upper caliper pin bolt has a bushing as part of the bolt. The lower caliper pin bolt is of a solid design.
  5. Install the caliper pin bolts and torque to 38 ft-lbs (51 Nm) (1996 - 1999), 63 ft-lbs (85 Nm) (2000 – 2005).
  6. Install the brake hose bolt with new copper brake hose gaskets to the brake hose and to the brake caliper, torque to 33 ft-lbs (45 Nm) (1996 – 2001) 32 ft-lbs (43 Nm) (2002 – 2005).
  7. Bleed the brake system.
  8. With the engine OFF, gradually apply the brake pedal to approximately 2/3 of its travel distance and slowly release the pedal. Wait 15 seconds and do it again until a firm brake pedal is obtained.
  9. Remove the 2 wheel lug nuts to retain the rotor to the hub.
  10. Install the tire and wheel assembly.
  11. Lower the vehicle.
Rear

Jul 08, 2010 | 1999 Buick LeSabre

1 Answer

How to change brake pads on 1998 daewoo laganza


I am assuming since you said "pads" you are reffering to disc brakes. Jack up car. Remove wheel. Unbolt and remove brake caliper. Remove old brake pads paying attention as to how they were attached and where they were placed. Using a C-clamp, push plunger of caliper back in as far as it will go. Put new pads on to caliper. Bolt caliper back in place. Install wheel. Remove jack.

May 17, 2010 | 1999 Daewoo Leganza

1 Answer

Rear pad replacement


the caliper has 2 bolts that must be removed and the caliper then comes out.you will after removing the old pads need a caliper piston compressor tool or the new pads will not fit.If you want to remove the rotors,you will need to undo the caliper bracket bolts and remove the bracket.Then the rotor will have to be hit a few times in the center by the studs with a hammer to knock it loose.Be careful not to hit the studs,as the threads can be damaged.Apply a silicone brake lube to the metal pad backing plate and lube the caliper slide pins after cleaning the old lube off.Do not use never sieze on brake parts.Be careful not to get brake lube on any pad surface.use a brake cleaner to remove it if you do.Shims have to be used if they are equipped with them or the brake pads will vibrate.

Apr 13, 2010 | 1999 Mercury Sable

1 Answer

Rear brake job


pull the two bolts holding the caliper on and pull the caliper off now get a C clamp and compress the piston all the way into the caliper now remove the two bolts in the caliper hanger and remove the hanger now the caliper should just pull off ( if corroted hit it with a hammer ) now just put every thing back to gether the way they came off...............WHEN DONE WITH THE BRAKE JOB MAKE SURE TO START THE TRUCK AND PUMP THE BRAKES UNTIL THE PEADLE IS HARD. YOUR PEADLE WILL GO RUTE TO THE FLOOR AT LEAST ONE TIME MAYBE MORE.

Jan 06, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Is there a torque spec on the spindle nut for the rear caliper on a 1999 Chevy Silverado 4x4 V8 5.3


  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Nov 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Change brake pads on 1999 GMC safari


jack up veh remove tire on back of caliper there are 2 bolts not the bolts on backing plate on the caliper remove caliper up and off pads remove pads using one of the old pads and a c-clamp carefully and slowly compress the caliper pistons back flush when done using a piece of wire hang caliper out of way check rotors if need to be cut remove and cut or if needed replace with new apply anti squeal lube on the backing of both pads reinsert pads bolt on caliper done

Sep 30, 2009 | 2000 GMC Safari

2 Answers

Replaceing brake caliper on driver side


I am assuming that you mean the brake line is made into the caliper. You will need to trace the brake line backward til you find the junction at the frame and disconnect it there. good luck. Dont forget to rate.

Mar 10, 2009 | 1999 Oldsmobile Alero

1 Answer

Changing rear rotors


remove the wheel, remove the calipers (two bolts, 12mm head),
you'll have to hold the slides with a 14mm to keep them from spinning while you remove the caliper bolts.
remove the caliper brackets, (two bolts with threadlocker 18mm head I think, get ready for the fight),
remove the little clips from the wheel studs (usually you can pry them up to the threads with a screwdriver then just spin 'em off)....that should do it....pull off the rotor.

Jul 21, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...