Question about Chevrolet Chevy

1 Answer

How do you remove the latch on the rear window of a 2002 blazer? Do I need to remove the trim? I need step by step instructions because the latch tries to open but will not release.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,050 Answers

Pull back the trim a little from the inside, and spray WD-40 or comperable on it to see if it will free up.

Posted on Jul 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

When i use the key fob to lock the doors the back glass dont lock, ???????


This solution applies to models:
2002-2007 Chevrolet Trailblazer, Trailblazer EXT and Trailblazer SS
2004-2007 Buick Rainier
2002-2007 GMC Envoy, Envoy XL, and Envoy Denali
2002-2004 Oldsmobile Bravada
2005-2007 Saab 9-7x

Condition/Concern:
Rear liftgate glass will not lock when using the key fob or door switch unless the lock button is pressed a second time. All other doors will lock normally. This could be the result of the liftgate glass lock rod not adjusted correctly. This lock rod travels from the liftgate lock actuator to the glass release push-button cylinder.

Recommendation/Instructions:
Remove the inside rear liftgate trim panel. Disconnect the threaded lock rod clip at the end of the push-button glass release and rotate this clip 1 complete turn at a time making the lock rod longer. This will be the only threaded lock rod visible when the trim panel is removed and the liftgate is raised.
Note: For the rear glass to release, the rear liftgate latch must be in the closed position. For test purposes only, this latch can be made closed to make this lock rod adjustment.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Apr 25, 2010 | 2006 Chevrolet Trailblazer

1 Answer

1996 chevy blazer 4wd rear hatch and window does not open. How can I maually open the rear hatch without taking off the panel


owners manual page 2-9 peel back or **** the carpet locally to expose the access hole in trim panel on endgate use a thin screwdriver to reach through the access holes in both th trim panel and the hardware cover. pry the release lever toward the passenger side until the glass latch pops open.

Oct 15, 2009 | 1996 Chevrolet Blazer

1 Answer

How to remove door panel on 1999 grand cheeroke, window is off regulator


Not that difficult of a task, it would be wise to get a service manual with step by step instructions and pictures. Factory ones are here for $20 bucks http://www.promanuals.net/dodgejeep.html

Trim
(1) Remove trim plug from mirror flag bezel.
(2) Remove screws attaching trim panel to door
(3) Using trim remover detach trim panel perimeter push-in fasteners from
door inner panel.
(4) Lift trim panel upward and separate from door.
(5) If equipped, disconnect harness connectors for
power accessories.
(6) Disconnect latch rods from inside handle actuator.
(7) Separate trim panel from vehicle.

Window Regulator
(1) Remove front door glass, (you may be able to access the regulator if the window is up)
(2) Loosen bolts attaching regulator to inner door
panel
(3) Remove bolt attaching regulator to inner door
panel
(4) Lift regulator upward to disengage bolts from
door inner panel.
(5) Disengage power window regulator harness
connector, if equipped.
(6) Remove regulator through access hole in door.


Jul 06, 2009 | 1999 Jeep Cherokee

1 Answer

Actuator removal


please rate as solved if this is what you need. You will need to borrow a heavy duty riveter from autozone or wherever you buy the lock cylinder from.


Removal
  1. NOTE: The rear door window glass must be completely raised.
    Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Trim Panel —Rear Door, Expedition Removal
  1. Remove the power window switchplate (14524).
  1. Disconnect the electrical connector.
  1. Remove the rear door handle trim cover.
  1. Remove the rear inside door handle.
    • Remove the door handle bolt.
  1. Remove the rear door trim panel screws at bottom of panel.
  1. s2j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the rear door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the rear door trim panel (27406).
  1. Remove the rear door watershield.
  1. Disconnect the power door lock actuator electrical connector.
  1. Drill out the power door lock actuator rivet.
9ac2386.gif
  1. Remove and discard the screws.
  1. Remove the power door lock actuator.
    • Disconnect the power door lock actuator rod.
Installation
  1. NOTE: Use new screws when installing the rear door latch.
    To install, reverse the removal procedure.
    • Use Heavy Duty Riveter to install the new rivet.

Jun 14, 2009 | 2002 Ford Expedition

1 Answer

2002 Explorer rear liftage latch replacement


Liftgate Latch Remote Control Removal and Installation
  1. Remove the liftgate trim panel. For additional information, refer to Section 501-05.
  1. Remove the watershield.
  1. Disconnect the actuator electrical connectors.
    a0023946.gif
  1. Disconnect the liftgate window glass latch release cable.
    1. Release the cable conduit.
    1. Disconnect the cable.
    a0023921.gif
  1. Disconnect the liftgate latch release cable.
    1. Remove the cable conduit.
    1. Disconnect the cable.
    a0023919.gif
  1. Release the exterior liftgate release handle actuating rod.
    1. Open the clip.
    1. Release the rod.
    a0023942.gif
  1. Remove the bolts and the liftgate latch remote control.
    a0023922.gif
  1. To install, reverse the removal procedure.
    • Transfer parts as necessary.

Jun 01, 2009 | 2002 Ford Explorer

2 Answers

2002 Explorer rear liftage latch replacement


Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  2. Remove the watershield.
  3. Remove the bolts and the liftgate latch.
    • Discard the bolts.
    a0023920.gif
  1. Disconnect the liftgate ajar switch electrical connector.
    a0023947.gif
  1. Disconnect the release cable.
    1. Disconnect the cable conduit.
    1. Disconnect the cable.
    a0023919.gif
  1. To install, reverse the removal procedure.
    • Transfer parts as necessary.
gate latch.

Apr 10, 2009 | 2002 Ford Explorer

1 Answer

Rear hatch window will not release


This is a common problem on the blazer. If you can hear the rod actuator working, then the actuator rod to latch rod connector has broken. It's plastic, and a poor GM design.
To get the rear hatch open you will need to manualy release it. It can be done by working as much of the plastic tailgate trim you can get loose, from around the top center of the gate, where the latch is. remove the 2 screws that hold the handle on and remove handle. Then pry as much as you need to access the c type latch, and release it by moving it... it's spring loaded and will only move one way. Haveing someone help you lift the hatch while you unlatch it from inside the vehicle helps. After you get the hatch up and the tailgate folded down, make sure the latch is locked in the open position.
The actuator can be repaired, i've done it several times. GM will try and sell you a new one, which is rather costly compared to the $8.00 piece of plastic you need.
Good luck and i hope this helps.

S.W. Brown
Level II+ diesel and heavy equipment tech.

Feb 22, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...