Question about Toyota Cars & Trucks

Open Question

Valve clearance for Toyota tazz 2e engine - Toyota Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: toyota 2e engine

Hi,

The only positive way to check if the oil pump is working and therefore there is correct oil pressure is to temporary install a non-electrical oil pressure gauge that uses a small copper tubing to sample the oil/pressure and drive a needle on the gauge. Depending on temperature, idle should register about 20+psi. Having done this and confirmed that indeed there is sufficient oil pressure then it may simply be a defective oil sending unit. Otherwise, no or low oil pressure at idle is an indicator that the engine needs to be opened up again.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.


Posted on Jul 24, 2008

  • 1 Answer

SOURCE: Toyota Tazz oil pressure problem

Did you prime the new pump properly before installing?

Posted on Jan 23, 2010

  • 2 Answers

SOURCE: 1986 toyota corolla 2E engine high fuel consumption

why does my normal rpm always bug down when the engine start?and when I started to use the air con, the rpm was playing. It doesnt go on a certain point. it always range at 800rpm then it will down to 700. what am I might do to solve this probem?

Posted on Mar 13, 2010

  • 156 Answers

SOURCE: valve tappet clearance of toyota 7k engine

7k clearances are ( HOT ) Inlet 0.008 in ( 0.20 mm )
Exhaust 0.012 in ( 0.30mm)

Posted on Mar 24, 2010

solarstarene
  • 159 Answers

SOURCE: whats the valve clearance for toyota 4k engines

valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.

Posted on Mar 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi how to replace piston rings for Toyota Tazz 2E engine


remove engine from car , remove engine head , remove oil pan , remove each rod from cylinders

Jul 04, 2017 | Toyota Cars & Trucks

1 Answer

I NEED TO SET TIMMING IN MY TOYATA TAZZ 1.3 2E ENGINE


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Dec 03, 2016 | Toyota Cars & Trucks

1 Answer

How many intake valves does a toyota tazz 2e engine 2004 model have


earlier 2Es have one inlet one exhaust
after the east west front wheel drive were introduced
most 2E toyota engines have three valves per cyl
two inlets and one exhaust

if you need the correct information on your 2004 2e engine
,,,,undo the rocker cover

e397a648-22cf-4373-b847-0ca46d719837.jpg

Jun 28, 2016 | Toyota Cars & Trucks

1 Answer

I have a toyota tazz 1.3 2e engine,i rekitted the carb n now it doent want to idle.please help


Re-adjust the jet screw on carb turn all the way in then turn 11/4 turn then go from there in or out. Reset idle screw. Make sure all vacuum lines are all in right place.

Jun 11, 2016 | Toyota Cars & Trucks

1 Answer

2003 Tazz, 2E engine. Why is it misfiring, jerking, and leaking oil?


you have 2 different problems misfire and jerking sounds like ignition, oil leaks are possible gasket problems.

Jul 07, 2015 | Toyota Cars & Trucks

4 Answers

What are the valve clearances for a 2e 12 valve engine?


I have Toyota Corolla EE80 2E engine with 12 valves. I recently top overhaul but the engine is not running in perfect condition. The engine rpm goes up and down (engine shaky). I set the rpm around 1200, if i set it lower than that the engine will stop. I check the engine timing with both the cam and crank on the correct mark. Sounds like the carburetor failure but i had service it but still the same. If i turn the distributor to the right (******) the engine rpm drop, than i turn it to the left (advance) but the rpm drop too, as i know the engine rpm should raise high and could hear the pinking sound from the valves if the the engine accelerate. For your info, i bought the cylinder head from someone who previously general overhaul his engine about 6 months ago. He dismantle his engine because of con rod problem. I just fix the cylinder head to my engine without grinding and adjusting the valves because it had been grind and adjusted 6 months ago. I check the spark plugs but look all black. I pull the plug cable one by one during the running it sounds all ok. Now i wonder what is actually wrong with the engine? Do i need to adjust the valve clearance too? What is the valve clearance for both exhaust and inlet, hot and cold? If i do the valve adjustment and yet still the problem, what is next?

Jan 02, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Toyota 1.3 2e


what valves are you refering to? there is many valves in a car other than the engine valves

May 31, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...