Question about Cars & Trucks

Open Question

How to remove the cooling fan shroud from a 2008 chevy uplander

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 186 Answers

SOURCE: radiator cooling fan 30 amp. fuse keep blowing

The fan may run with jumper wires but if it''s blowing the 30 Amp Maxifuse it's needs a new or used fan motor.It's pulling too many amps.I have almost never seen a fan relay concern.Only other thing you may check is the wiring down near the fan shoud I have seen the 2 wires get loose from the conduit & melt onto exhaust manifold.Hope tHis Helps

Posted on May 12, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: Fan shroud removal

You need to take the fan off as well if you have a mechanical fan. IF you have the electric fan in the shroud, it comes out with the shroud.

Posted on Jul 23, 2009

duane_wong
  • 6826 Answers

SOURCE: I need to remove the cooling fan shroud from my

Engine Fan REMOVAL & INSTALLATION 3.8L Engines

  1. Disconnect the negative battery cable.
  2. Remove the radiator upper sight shield.
  3. Disengage the electrical connector, then remove the integrated relay control/constant control relay module assembly located on the radiator support.
  4. Disconnect the fan electrical connector. Fig. 1: Disengage the fan electrical connector 86873115.jpg

  5. If necessary, remove the air bag crash sensor.
  6. Unbolt the fan/shroud assembly from the radiator and remove. Fig. 2: Unbolt the fan assembly from the radiator 86873116.jpg
    Fig. 3: Remove the fan from the engine 86873117.jpg
    Fig. 4: Slide the fan as an assembly up and away from the radiator. Be careful not to dislodge the mounting stud on the left side. 93143p56.jpg

  7. Remove the retainer and the fan from the motor shaft and unbolt the fan motor from the shroud.
  8. Installation is the reverse of the removal procedures. Tighten the fan shroud retaining bolt to 23–33 inch lbs. (2.6–3.7 Nm). Tighten the fan shroud retaining nut to 71–106 inch lbs. (8–12 Nm). Fig. 5: Constant control relay module location — 3.8L engines 86873118.gif
4.6L Engine
  1. Loosen the fan clutch-mounting shaft from the water pump hub.
  2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.
  3. Lift the fan and clutch assembly and the fan shroud from the vehicle.
  4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  5. Assemble the fan and fan clutch. Tighten the retaining bolts to 15–20 ft. lbs. (20–27 Nm).
  6. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37–46 ft. lbs. (50–62 Nm).
  7. Slip the shroud into the lower mounting clips and install the shroud retaining screws. Fig. 6: Fan and fan clutch assembly — 4.6L engine 84173064.jpg
5.0L Engines
  1. Loosen the fan clutch-to-water pump hub retaining bolts.
  2. If necessary, remove the drive belt from the water pump pulley.
  3. Remove the fan shroud upper retaining screws. Lift the shroud to disengage it from the lower retaining clips.
  4. Remove the fan clutch-to-water pump hub bolts and remove the fan and clutch assembly and the fan shroud.
  5. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  6. Assemble the fan and fan clutch. Tighten the retaining bolts evenly and alternately to 12–18 ft. lbs. (16–24 Nm).
  7. Install the fan and clutch assembly and the fan shroud.
  8. Install the fan clutch-to-water pump hub bolts.
  9. Slip the shroud into the lower mounting clips and install the shroud retaining screws.
  10. If removed, install the water pump drive pulley and adjust the belt tension; refer to Section 1.
  11. Tighten the fan clutch-to-water pump hub bolts evenly and alternately to 15–22 ft. lbs. (20–27 Nm). Recheck the belt tension.
prev.gif next.gif

Posted on Jul 14, 2010

  • 1608 Answers

SOURCE: my 2008 chevy uplander engine

You will need to get the codes checked.This will help in finding out what is causing the light to come on.Once you get the code or codes we can find out what could be causing the problem.Let me know when you get the codes and I`ll be glad to help you out.Good luck.

Posted on Mar 01, 2011

  • 1 Answer

SOURCE: I'm getting trouble code p1174

i have an 2007 chevy uplander flexfuel i keep getting p1174 also i have replaced the the o2 sensors and the light keeps coming on
i belive it has something to do with the fuel injection system

Posted on Nov 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding the coolant system 2005 chevy uplander


Bleeding the coolant system Leisa, Check the attached links,instruction and guides on bleeding cooling systems. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Fill Bleed Coolant Chevy 3 4L V6
Bleeding Air In Cooling System
Coolant Flush How to Chevrolet Uplander 2005 2008 2008 Chevrolet Uplander...
How To Bleed Cooling System EricTheCarGuy


May 21, 2016 | Cars & Trucks

1 Answer

Rear blower not working on 2008 Chevy uplander


First think I would do is take an ohm meter and see if you are getting power to the rear blower resister. They go bad before the blower does. Also check your fuses and rear fan blower relay. Good luck.

Jan 07, 2015 | 2008 Chevrolet Uplander

1 Answer

How to change a coolant fan for a 2001 impala


  1. Disconnect the negative battery cable.
  2. Partially drain the cooling fan.
  3. Raise and support the vehicle. Refer to Vehicle Lifting.
  4. Remove the transmission oil cooler lines from the retainers at the bottom of the cooling fan shroud.
  5. Remove the lower fan shroud push pin retainers.
  6. Lower the vehicle.
  7. Remove the right and the left engine mount struts.
  8. Remove the left front fender upper diagonal brace.
  9. Remove the radiator inlet hose from the radiator.
  10. Remove the air cleaner assembly.
  11. If equipped remove the cooling fan heat shields.
  12. Disconnect the cooling fan shroud electrical connectors.
  13. Remove the cooling fan shroud bolts.
  14. Disengage the cooling fan shroud clip from the top of the radiator.
  15. Remove the cooling fan shroud.


25010346-uuob5xk5qpmufdktz2iyu4qm-2-0.gif

Aug 25, 2014 | 2001 Chevrolet Impala

1 Answer

How do I remove a radiator in a 2000 Chevy Silverado 1500 pickup


Gasoline Engines
  1. Drain the cooling system.
  2. Unfasten the upper fan shroud bolts and remove the upper fan shroud.
  3. If equipped, remove the upper panel fasteners and the panel.
  4. If equipped, remove the upper insulators and brackets.
  5. Disconnect the radiator upper and lower hoses and, if applicable, the transmission coolant lines.
  6. Remove the coolant recovery system line, if so equipped.
  7. Remove the oil coolant lines, if equipped.
  8. Remove the lower fan shroud bolts and the lower fan shroud.
  9. Remove radiator from the lower brackets and insulators.

Jul 28, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

Chevy Uplander a/c cuts out when hot and the cooling fan is always on


If the check engine light is not on, I would check voltage to the compressor clutch when it fails. Could be the clutch or a relay.

Aug 29, 2012 | 2008 Chevrolet Uplander

3 Answers

2008 Chevy Uplander has 21,000 miles. Nno heat from rear heater at idle. Disconnected hoses and flushed, water flowed good. Reconnected hoses and still no heat. Raised idle to 2000 rpm and got good heat....


Uplanders with the 3.9 engine are prone to no heat at idle speeds. Probably weeping head gasket. Air bubble trapped. Dealers will remove rad cap and let it sit at about 25 deg. angle for a couple hours. Good for awhile.

Nov 15, 2010 | 2008 Chevrolet Uplander

1 Answer

2005 Jeep Liberty overheats at idle but while in movement temp returns to normal.


Check to see if the fan on the radiator is working at idle.

Here's information on how to change the fan if needed:

Engine Cooling Fan Removal & Installation 2.4L Engine To Remove:
  1. Remove the coolant bottle and set aside.
  2. Remove the power steering reservoir and set aside.
  3. Disconnect the cooling fan connector.
  4. Remove the cooling fan mounting screws and the cooling fan.
To Install:
  1. Install the cooling fan and the mounting screws. Tighten to 50 in-lb (5.5 Nm).
  2. Connect the cooling fan connector.
  3. Install the power steering reservoir.
  4. Install the coolant bottle.
3.7L Engine To Remove:
NOTE: If the fan blade is bent, warped, cracked or damaged in any way, it must be replaced ONLY with a replacement fan blade. DO NOT attempt to repair a damaged fan blade.
NOTE: For 3.7L Heavy Duty/Max Cool/Trailer Tow cooling package, the viscous fan cannot be removed separate from the shroud. Both fan and shroud must be removed together.
  1. Disconnect battery negative cable.
  2. Using special tool #6958 spanner wrench and #8346 adapters, remove the viscous fan from the water pump.
  3. Gently lay fan into shroud.
  4. Disconnect the electrical connector for the electric fan, then disconnect connector from shroud.
  5. Remove the two fan shroud mounting bolts connecting the fan shroud to the radiator.
  6. Remove the shroud and fan from the vehicle.
To Install:
  1. Install fan shroud assembly into the vehicle. Tighten fan shroud to radiator bolts to 50 in-lb (5.5 Nm).
  2. Install shroud mounting bolts tighten bolts to 89 in-lb (10 Nm).
  3. Connect fan motor wire connector to harness connector, and attach connector to shroud.
  4. Connect negative battery cable.
  5. Start engine and check fan operation.

Aug 31, 2010 | 2005 Jeep Liberty

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    36 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14398 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...