Question about Cars & Trucks

Open Question

I can't find the Vallet switch all I see is the windshield transmitter, it does have a button. I'm trying to program key fob. Pleaise help

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 82 Answers

SOURCE: Car will not unlock.

To get inside the car .... Use the key in the lock cylinder, unlock the drivers door to get inside. You shouldn't have to reprogram the fob unless it or the keyless module was changed. There may be a blown fuse that supplies the keyless control module (check the owners manual for location). or wires that lead into the Drivers door may be damaged ... The keyless module is located inside the drivers door at the bottom behind the door panel ... do the unlock/lock and trunk release switches on the inside of the drivers door operate the locks and or trunk release? If so it is not the fuse ... and not the wires to it ... And it could be your BCM body control module, located in the dash board to right of your gas petal. Because the number entry keypad (code for that is on the inside of the right passenger trunk bracket arm) also doesn't work I assume it's not the key fobs themselves. Your 98 manual is correct for your car.

Posted on May 04, 2009

Ad
  • 84 Answers

SOURCE: Chevrolet blazer 2001 programming transmitter FOB

lol...turn the key on..there a reset button on the dash that show mile how far u drive..well push and hold while the ignition on and engine off until it blink..than start tap it until you came across door lock/alarm...ok ...here the trick..leave the setting on the alarm. than u can press an hold unlock n lock until u hear the door lock than u release turn key off n on than off again...and than try your transmitter

Posted on Apr 21, 2010

  • 11800 Answers

SOURCE: MY PT Cruiser Functional transmitter

If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Posted on Sep 06, 2010

  • 267 Answers

SOURCE: I have a 94 Buick century. I need to program this new key fob transmitter for entry

Many full service locksmiths have the equipment to clone your old fob if it is a factory equipment. Otherwise the dealership should be able to get you another but you will probably need your VIN and if you have a spare key you should take it with you to the dealer.

Posted on Feb 05, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program a 2004 Nissan Maxima key fob?


Free Nissan Keyless Remote Programming Replacement Key Keyfob Maxima...

2004 Nissan Maxima Key Fob Programming Instructions

2004 Maxima

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
  1. Close and lock all doors with the driver's side power lock/unlock switch.
  2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
  3. Insert key into the ignition cylinder and turn to the ACC position.
  4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.
  5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).
  6. Turn the key to the OFF position, remove keys from the ignition,
    unlock doors using the driver's side power lock/unlock switch and open the driver side door.

Mar 09, 2015 | Nissan Cars & Trucks

1 Answer

Doors dont lock with secrity fob


The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

Sep 05, 2012 | 2004 Chevrolet TrailBlazer

2 Answers

The lock button on my key fobs will not lock the doors on 06 honda crv


CHeck to see if it is the right battery - Should be a CR1616 - previous year models, had a different battery.

Does the light come on on the key fob, when you push the button?

You may have to reprogram the remote - check the owners manual for instructions - if you can't find them...

Programming the Transmitter
NOTES:
• The system accepts up to three transmitters. The
transmitter codes are stored in a stacking-type
memory. If a fourth transmitter code is programmed,
the code for the first transmitter is erased.
• Entering the programming mode cancels all learned
transmitter codes, so none of the previously
programmed transmitters will work. You must
reprogram all of the transmitters once you are in the
programming mode.
• You must complete each step within 4 seconds of
the previous step to keep the system from exiting the
programming mode. Program the transmitters within
10 seconds.

1. Turn the ignition switch to ON (II).
2. Press the "Lock" or "Unlock" button on one of the
transmitters. (An unprogrammed transmitter can be
used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the
same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the "Lock" or "Unlock" button on the same
transmitter. Make sure the power door locks cycle
to confirm that the system is in programming mode.
7. Within 10 seconds, press the "Lock" or "Unlock"
button on each transmitter. Make sure the power
door locks cycle after you press each transmitter
button to confirm that the system accepted the transmitter's code.
8. Turn the ignition switch to LOCK (0) to exit programming mode.


IF so, and more likely, the fuse on the car side of the remote, is probably gone.

Apr 25, 2012 | 2006 Honda CR-V

1 Answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...


reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

May 18, 2011 | 1999 Toyota Camry Solara

1 Answer

How do i program the remote for my car?


PROGRAMMING REMOTE KEYLESS ENTRY TRANSMITTERS (RKE)

1. Install scan tool

2. Turn the ignition switch to ON - do not start engine

3. Select "Remote Function Actuation" with the scan tool

4. Select "Special Functions"

5. Select "Program Key Fobs"

6. Select the number of key fobs to be programmed

7. Press and hold the LOCK and UNLOCK buttons on the first transmitter simultaneously for approximately 15 seconds. The door locks should cycle (Lock and unlock) to confirm that the programming of the first fob is complete.

8. If you are programming more than one transmitter, repeat the previous step for each transmitter for up to four transmitters in total.

9. Remove the scan tool

10. Exit the vehicle and operate transmitter functions to verify correct programming and operation.

Apr 20, 2011 | 2003 Saturn L-Series

1 Answer

Key fobs do not lock/unlock doors, horn or trunk release. Batteries in key fob is good, fuses are good. What's next/


Retrain the fobs following the procedure in your owner's manual:

 Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters.
 Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on
program mode in close proximity.
1. Sit in the driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all vehicle doors.
4. Press and hold unlock on the door lock switch.
5. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do
not rotate the ignition lock cylinder.
6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain
in the LOCK position for the rest of the procedure.
7. Release the door lock switch. You will hear three chimes. This chime feedback indicates that transmitter
programming is active.
8. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 12
seconds.
You will hear two chimes. This chime feedback indicates that the transmitter has been
programmed successfully.
9. Repeat step 8 for the rest of the transmitters (for a total of 4 transmitters).
10. Exit this procedure by removing the ignition key from the ignition lock cylinder.

Feb 12, 2010 | 1999 Oldsmobile Intrigue

1 Answer

1999 Chrysler Town and Country


Have you you tried just re-programming all of your remotes? I just added a "new" (from Ebay) remote and when re-programming, had to do them all. Here's how... 1. Using a functional key fob transmitter, unlock the vehicle and disarm the Vehicle Theft Security System. 2. Insert ignition key into the ignition switch. 3. Turn the ignition switch to RUN position without starting engine. 4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum four seconds (maximum ten seconds) 5. While holding UNLOCK button, and before ten seconds passes, press and release the PANIC button. A single chime will sound to verify that the RKE module is set to receive the new Vehicle Access Code(s) 6. Within 30 seconds of the chime, press and release the "LOCK" and "UNLOCK" buttons on the transmitter at the same time. Then press any one of the buttons. The BCM will sound an abbreviated chime to acknowledge that the programming of the transmitter has been completed and was successful. 7. Repeat step 6 for all transmitters that will be used with this vehicle (up to 4 total) 8. Programming mode will last for 30 seconds. To get out of programming mode sooner, turn the ignition OFF. A single chime will sound to verify that the RKE module will no longer accept additional Vehicle Access Code(s) 9. When Vehicle Access Code(s) programming is complete, turn the ignition switch to the OFF position and verify RKE system operation using each key fob

Aug 03, 2009 | 1999 Chrysler Town & Country

1 Answer

How to program key fob. I have the fobs.


Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Jun 25, 2009 | 2002 Chevrolet Tahoe

2 Answers

How do i program a new remote for my 2001 chevrolet blazer?


You may program up to 4 transmitters, using following procedure:

Transmitter Programming Procedure (No Tools Required)
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation



May 06, 2009 | 2001 Chevrolet Blazer

1 Answer

Programming a 1995 toyota avalon key fob


To program a remote... note that you must not delay more than 10 seconds between any of the operations.

Driver's door open, all other doors closed, key removed from the ignition switch.

Insert key into ignitions switch, then remove it.

Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.

close and re-open drivers door.

Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times

Insert Key into ignition switch.

Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.

Remove Key from ignition switch.

System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.

Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.

Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.

NOTE: to exit programming mode, close drivers door or insert key in the ignition.

NOTE: a maximum of 4 remote transmitters can be programmed

Oct 13, 2008 | 1995 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...