Question about Cars & Trucks

1 Answer

How do i check oil level on ptc1 cultivator it has three alen screws on drive shaft

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 139 Answers

Hmm, should be a bolt/nut on the right side of the crankcase. if you mean eckman 2 stroke?

Posted on Apr 19, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would make a trans squeal while driving down the road?


You don't say, Front or rear wheel drive. First check oil level, On rear wheel drive check the thrower plate on the tail shaft at the diff end is not bent and rubbing on the seal, A dry oil seal can make this noise.so can the U/Joints. on front wheel drive , check the cv joints , dry oil seals , the drive shaft inner cv joints have a thrower plate that may be bent. worn or binding brakes can make this noise also.

Sep 24, 2014 | Cars & Trucks

1 Answer

First thing in the morning, putting the car in reverse or drive after starting, the auto transmission makes quite a large bump. When warmed up the transmission is quite smooth when changing from drive to...


Hi no dipstick on these models there is a level screw on the bottom of gearbox,its a big allenkey with a small one inside if the small one is removed the oil must come dripping out if not the level is lower than the big level screw note do not remove big screw then all your oil will leak out and make sure the car is hot when u check oil level to get rite level.A other thing is I no there is software updates on the gearbox control units so if the oil level is ok get the car scanned at a dealer to check for uptades.hope this helps.regards

Jun 30, 2011 | 2005 Volkswagen Golf

1 Answer

When u are drving it jumps out of gears!


Hi there?
Make sure there is oil in the gearbox. There should a 8mm alen key bolt in front of the gearbox. The oil should be level with the base of the hole. If the oil level is ok then i'm affraid that the gearbox is worn out and it needs replacing or repairing.
Good luck........

May 21, 2011 | Ford Explorer Cars & Trucks

3 Answers

Just got 1996 chevy cavalier. Where do you add transmission fluid?


the transmission fluid goes down the dip stick hole ,either use a small funnel or special tranny fluid refill top up bottle

Feb 04, 2011 | 1996 Chevrolet Cavalier

1 Answer

How to check trasmission fluid no dipstick just a red cap


4T40E Automatic Transaxle CAUTION
Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of the transaxle fluid to exhaust pipe. The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
  1. The fluid level should be checked when the transaxle is near room temperature or at 104°F (40°C). To acquire this, left the car idle for 3-5 minutes with all of the accessories off. Fig. 5: Location of the fluid level screw and the fill/vent cap needed to check the fluid for the 4T40E automatic transaxle 87951085.gif

  2. Apply the brake, then move the gear shift selector through all gear ranges, pausing three seconds in each range. Shift the lever into P.
  3. Raise and safely support the vehicle.
  4. Place a suitable drain pan under the check plug to catch any fluid that may drip out.
  5. Remove the oil check plug. The oil level should be at the bottom of the oil check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the screw hole when the screw is removed.
  6. If fluid drains through the screw hole, the transaxle may have been overfilled. When fluid stops draining, then fluid level is correct and the check plug may be installed. If fluid does not drain through the screw hole, the transaxle fluid may have been low. Add fluid at the vent cap location in 1 pint increments until the oil level is at the bottom of the oil check hole.
  7. Install the oil check plug/fluid level screw and tighten to 10 ft. lbs. (14 Nm).
  8. Carefully lower the vehicle.
prev.gif next.gif

Jan 21, 2011 | 1997 Pontiac Sunfire

1 Answer

When driving my xj6 2003 model there is a thump


are the drive shafts ok ,check the oil level as well,start engine ,handbrake on and a brick behind the back wheels ,now drop into reverse and then wipe the dipstick and check oil level.If you have a later model you may have have it up on ramp and check oil level is to the filler plug level

Nov 22, 2009 | 1997 Jaguar XJ6

3 Answers

Why does my 1999 manual transmission chevy S-10 oil gauge go up and down as I drive?


normal - pressure drops off at idle and increases as engine speeds up.

Sep 17, 2009 | 1999 Chevrolet S-10 Pickup

1 Answer

I have a 2000 chevy cavalier Z24 and it seems to not have a dipstick to check transmission fluid how do you tell when it is low or does anyone know where it is


Let vehicle idle for three to five minutes with accessories off. Apply brake Move shift lever through all gear ranges, pausing three seconds in each range. Place shift lever in Park. Important: Vehicle must be kept level on the hoist. Raise vehicle on hoist. Place oil container under fluid level screw. it is near the bottom of the driveshaft Remove the fluid level screw with the engine running at idle. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap 1 PINT Increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. Install fluid level screw. Tighten

Jun 12, 2009 | 2000 Chevrolet Cavalier

2 Answers

Location of transmission (automatic) dipstick


You DO NOT have one.

There is a small bolt/plug in the transmission above the pan that needs to be removed. The fluid will run out if it's overfilled. The transmission needs to be at room temperature or a little warmer to check the level.


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
Inspect:
The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F).
CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.
The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.
WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine.
181efc6.gif
Adding Transaxle Fluid:
  1. With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  2. Install fluid level screw. Tighten 12 N.m (106 lb in)
  3. Lower vehicle
0e45832.gif

Mar 23, 2009 | 1996 Chevrolet Cavalier

1 Answer

50,000 mile service


48,000 miles or 48 months
Maintenance Service Schedule 2007 dodge
Change engine oil and engine oil filter
Rotate tires
Lubricate drivetrain / steering / suspension
grease fittings (if equipped)-except Powerwagon
Lubricate front drive shaft fitting
(2500 / 3500, 4X4 & Powewagon)
Lubricate tie rod end links - Powerwagon
Check automatic transmission fluid level
Check manual transmission fluid level
Check the coolant level, hoses and clamps
Inspect exhaust system
Inspect brake hoses and brake linings
Inspect the CV joints/U-joints (if equipped) and
front suspension components
Check spare tire for proper pressure & correct
stowage
Lubricate outer tie rod ends 2500/3500 4X4

51,000 miles or 51 months
Maintenance Service Schedule
Change engine oil and engine oil filter
Lubricate drivetrain / steering / suspension
grease fittings (if equipped)-except Powerwagon
Lubricate front drive shaft fitting
(2500/3500, 4X4 & Powerwagon)
Lubricate tie rod end links - Powerwagon
Check automatic transmission fluid level
Check manual transmission fluid level
Check the coolant level, hoses and clamps
Inspect exhaust system
Inspect brake hoses
Inspect the CV joints/U-joints (if equipped) and
front suspension components

Jan 04, 2009 | 2007 Dodge Ram Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...