Question about Cars & Trucks

Open Question

Pin out python 5706p wire forum

Pl I need more wire diagram step by step connection

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: i just need a small 7 pin wiring diagram to wire a...

facebook

Posted on May 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pcm wiring diagram


There isn't much to the wiring diagram There is only two wires to the N75 turbo control solenoid.Pin 2 on solenoid green and brown comes from the ECU pin 64 and Pin 1 Green and white wire goes to a 10 pin connector in the plastic channel on the left side of the engine bay pin 6 and then that then goes on to connection 2 (87) in dash panel wiring harness.

Jul 11, 2014 | 2000 Volkswagen Golf

1 Answer

Wiring diagram for 2004 toyota 4runner with jbl


It appears that red is a speaker connection and not power. The complete wiring diagram I'd in the link below.

speaker wire color Toyota 4Runner Forum Largest 4Runner Forum

Jan 26, 2014 | Toyota Cars & Trucks

1 Answer

I have a 2008 mazda 23 . All power windows except the drivers side front window will not close I opened them all fully and none will close or operate except the front drivers window which operates ok Any...


Welcome to FixYa

You will need to check all connections in door. Make sure to have a 12 volt test light, remove door panel and check window switch for power if ok go to motor hold test light to the hot wire to motor, use window switch does test light light up if so motor is bad.

Need help with door panel and testing with pin connector locations go to this site you with the diagrams and step by step diagrams .

Lee

leedavidian_162.png

Feb 10, 2011 | Mazda MAZDA3 Cars & Trucks

1 Answer

Looking for a wiring diagram / pin out on the air conditioning electrical connections for the pressure transducer on a 2006 dodge diesel


your local public library should have great resources online for free you can access with your library card just a suggesrion because online i find wiring diagrams to be expensive.
0423b4e.jpgdoes this diadram help? ihad to reduce the size for the forum hope it is readable

Apr 24, 2009 | 2006 Dodge Ram 2500

2 Answers

Hi in need of a wiring diagram fuse box Mazda bongo


look here: http://www.bongoforum.co.uk/forum/Blah.pl?

Apr 07, 2009 | 1997 Mazda MPV

1 Answer

Fitting a towbar for a caravan with 13pin europlug


black socket, black 7 core wire
pin 1 yellow left indicator
pin 2 blue, rear fog light
pin 3 white earth
pin 4 green right indicator
pin 5 brown right side/tail light
pin 6 red brake lights
pin 7 black left side/tail light

Grey socket grey 7 core wiring
pin 1 yellow, reverse
pin 2 blue, supplementary feed (ignition)
pin 3 white, earth
pin 4 green live feed (battery +)
pin 5 brown not connected
pin 6 red supplementary feed (ignition)
Pin 7 black earth

On the discovery there is a purpose made plug behind the panel on the drivers side rear, behind the rear lamp
i think the relay you have bought is for lamp failure you just need a normal 4 pin 30 amp relay.
Good luck Davelee

Mar 19, 2009 | 1997 Land Rover Discovery

1 Answer

Installing a 7-pin trailer towing recptical on a 1991 Ford F150.


I believe you can look up the manufacturer of the trailer plug kit and find the wiring diagram there. On alot of the trailer plug kits, they have pics and diagrams in the package. The 7 pin plug (truck side) is available with the pig tail set up that plugs directly into the wiring harness for the lights. Then all you would have to worry about is the 2 wires for the electric brakes.

Nov 29, 2008 | 1991 Ford F150

2 Answers

Diagnostic codes


Please rate me solved...thanks!
DTC P1259: VTEC SYSTEM MALFUNCTION
1. Perform PCM reset procedure. See SELF-DIAGNOSTICS - INTRODUCTION article. Start engine
and run at 3000 RPM with no loads and transmission in Park or Neutral until radiator fan comes on. Road
test vehicle. Accelerate in 1st gear to an engine speed over 4000 RPM and hold that engine speed for at
least 2 seconds. If DTC P1259 is not indicated during first road test, repeat road test 2 more times. If DTC
P1259 is indicated, go to next step. If DTC P1259 is not indicated, problem is intermittent. System is
okay at this time. Check for poor connections or loose wires at VTEC solenoid valve connector and PCM.
See ENGINE PERFORMANCE WIRING DIAGRAMS article. Repair as necessary.
2. Turn ignition off. Disconnect VTEC pressure switch 2-pin connector. Check for continuity between
VTEC pressure switch terminals. If continuity exists, go to next step. If continuity does not exist, replace
VTEC pressure switch.
3. Turn ignition on. Measure voltage between ground and VTEC pressure switch harness connector terminal
No. 2 (Blue/Black wire). If about 12 volts exist, go to next step. If about 12 volts do not exist, check for
an open or short in Blue/Black wire between VTEC pressure switch and PCM 31-pin connector "C"
terminal No. 10. Repair as necessary. If wire is okay, substitute a known-good PCM and recheck. See
SUBSTITUTING PCM in SELF-DIAGNOSTICS - INTRODUCTION article. If symptom or problem
goes away, replace original PCM.
4. Measure voltage between VTEC pressure switch harness connector terminals. If battery voltage exists, go
to next step. If battery voltage does not exist, repair open in Brown/Black wire between VTEC pressure
switch and ground connector located on left side of engine, under throttle plate, between end of radiator
hose and cooling fan switch. See ENGINE PERFORMANCE WIRING DIAGRAMS article. If wire is
okay , substitute a known-good PCM and recheck. See SUBSTITUTING PCM in SELFDIAGNOSTICS
- INTRODUCTION article. If symptom or problem goes away, replace original PCM.
5. Turn ignition off. Disconnect VTEC solenoid valve connector. Measure resistance between ground and
VTEC solenoid valve connector. See ENGINE PERFORMANCE WIRING DIAGRAMS article. If
resistance is 14-30 ohms, go to next step. If resistance is not 14-30 ohms, replace VTEC solenoid valve.
6. Remove VTEC pressure switch and install Pressure Gauge Adaptor (07NAJ-P07010A) and A/T Low
Pressure Gauge (07406-0070300). Reinstall VTEC pressure switch into adaptor. Connect tachometer.
Start engine and with no loads and transmission in Park or Neutral until radiator fan comes on. Because
engine is running with no load, oil pressure must be checked within one minute. Check oil pressure at
engine speeds of 1000, 2000 and 3000 RPM. If oil pressure is less than 7 psi (48 kPa), go to next step. If
oil pressure is 7 psi (48 kPa) or more, check VTEC solenoid valve. See SYSTEM & COMPONENT
TESTING article.
7. Turn ignition off. Disconnect VTEC solenoid valve connector. Connect a fused jumper wire between
battery voltage and VTEC solenoid valve connector. Start engine and check oil pressure at 3000 RPM. If
oil pressure is more than 57 psi (393 kPa), go to next step. If oil pressure is 57 psi (393 kPa) or less,
check VTEC solenoid valve. See SYSTEM & COMPONENT TESTING article.
8. Ensure jumper wire is still connected to VTEC solenoid valve connector. Start engine and allow it to idle.
Set engine speed to more than 4000 RPM and measure voltage between ground and PCM 31-pin
connector "C" terminal No. 10 (Blue/Black wire). See ENGINE PERFORMANCE WIRING
DIAGRAMS article. If battery voltage exists, go to next step. If battery voltage does not exist, replace
VTEC pressure switch.
9. Turn ignition off and disconnect jumper wire. Check for continuity between VTEC solenoid valve
harness connector and PCM 25-pin connector "B" terminal No. 12 (Green/Yellow wire). See Fig. 2 . See
ENGINE PERFORMANCE WIRING DIAGRAMS article. If continuity exists, go to next step. If
continuity does not exist, repair open in Green/Yellow wire between VTEC solenoid valve connector and
PCM 25-pin connector "B" terminal No. 12.
10. Check for continuity between ground and VTEC solenoid valve connector. See ENGINE
PERFORMANCE WIRING DIAGRAMS article. If continuity exists, repair short in Green/Yellow
wire between VTEC solenoid valve connector and PCM 25-pin connector "B" terminal No. 12. If
continuity does not exist, substitute a known-good PCM and recheck. See SUBSTITUTING PCM in
SELF-DIAGNOSTICS - INTRODUCTION article. If symptom or problem goes away, replace original
PCM

Jun 21, 2008 | 1999 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...