Question about Cars & Trucks

Open Question

Fork lift yale code 522739-6 , blows fuse f3 when turn key to start position

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Psych0Thrash
  • 53 Answers

SOURCE: crank no start

you've got an open wire in your ignition system that's making fuses blow, i had the same thing happen to me check the wire that runs from the starter to the main fuse box and the wire from the battery to the fuse box. It will only be the wires that carry voltage, none of the ground wires should do that

Posted on Aug 19, 2008

Ad
  • 399 Answers

SOURCE: 2001 Mercury Mountaineer keeps blowing the PCM power diode (fuse #19)

Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

Posted on Sep 18, 2008

  • 512 Answers

SOURCE: no turn no start. blows the start fuel fuse intermitantly.

experience says the starter is the likely culprit....it has a bad spot in it

Posted on Nov 16, 2008

  • 5537 Answers

SOURCE: 2000 Grand Voyager blowing the ignition fuse

Was the old fuel pump bad? It might be worth the cost to replace the ignition switch. The wires to the fuel pump would be a second guess if the old pump was bad and burnt the wires before the fuse went. When you eliminated the fuel pump you also eliminated the wires to the pump and it started. Then you replaced the pump, but not the wires. The ignition switch is the other end of the circuit.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: My 2002 Sebring keeps blowing the starter fuse?

Mine is doing the same thing. We are getting ready to replace the starter. Hopefully that is the problem. I'll let you know how it turns out.

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Buick century custom and I had drained my reservoir. Now everything I attempt to start my car my pcm fuse blows instantly. I've replaced my ignition switch and fixed my ignition column yet...


pcm fuse blows instantly ???? What number fuse , how many amps ? Where is it located ? under hood fuse box . ECM fuse 10amp ,underhood fuse box ???? When does the fuse blow ? when you turn the key to the start position . How about when you turn it to just on position ? Replacing the ignition switch an the column ????? Why did you replace these ? You think it was going to fix the problem ? or someother problem ? Bad computer maybe .

Sep 16, 2017 | Buick Cars & Trucks

1 Answer

2007 ford freestar will fuse # 40 in the underhood fuse panel when the key is turned to the run/start position. It would blow before when it was running and cause vehicle not to shift. Had the transmission...


Any applicable trouble codes? Several systems get voltage off that same fuse. oxygen sensors-- canister purge solenoid--ac compressor relay--imrc, intake manifold runner control, has to do with induction-- breathing. And tranny control.
If it blows as soon as the key is turned on, maybe you can narrow it down by unplugging each system one at a time? That may not be conclusive, any system you unplug, there will be less amp draw on the fuse. Just a thought.

Jul 24, 2017 | Ford Cars & Trucks

1 Answer

Hi,when I turn the key over it automatically blows a fuse!! Please Help?


Check the entire engine wiring harness, somewhere there is a wire or wires that are pinched or have rubbed through and grounded to the metal of the chassis, pay close attention where the wires move a lot. There is no quick fix, just careful examination for damaged wires. Obtain a wiring diagram and trace down the circuit that the fuse powers would also be very helpful.

Dec 23, 2016 | Cars & Trucks

1 Answer

What does fault 108-1 mean on a Yale forklift


Troubleshooting Yale - Forkliftaction.com

www.forkliftaction.com/forum/threadbybrand.asp?brid=97
No Trans Braking Error code 524264-14. Discussion started: 5 .... Error code 108-1displayed. Discussion ... Yale forklift has perkins 4203.2 engine oil capacity?

Oct 23, 2015 | Cars & Trucks

3 Answers

There is no reaction when turning the key to start the car


Turn key to On.
Turn on headlights manually... Do they come on?
Are there any lights on the dash?
If yes to these, battery is possibly not the sole problem.
Check for good, tight and clean connections at battery terminal posts!
If yes to above, continue on & get a helper... Turn key past on, to Start position.
Do you hear a click sound at time key is turned to Start?
If yes, then ignition switch is not problem, starter relay is getting power, and is now sending power to starter, but starter is not working.
Pic any No's... Then look there.
Good luck.

Mar 29, 2015 | 2005 Ford Focus 1.6

1 Answer

I have a 2005 land rover freelander in the engine fuse box the f3 fuse keeps blowing 15amp you start the truck go down the road fuse blows it starts runing ruff stop turn off truck then try to start wont...


15 amp is a fair current draw and for it to blow after a few minutes means that there is a short in that circuit that is allowing a drain to earth that just exceeds the 15 amp. It is in the ignition part of the system and may be a bad connection ( water ) or a problem appearing in the ECM or relay . Run fault codes to find the area of the fault. Because it is taking time to blow the fuse, it will be difficult to find. Check all wiring for rub marks .

May 07, 2014 | 2005 Land Rover Freelander

2 Answers

20 amp fuse keeps blowing engine won't start, fuse


I am a mechanic,i had that same problem where my engine 20amp fuse were blowing....i fixed it...problem were a broken wire in the harnace on the side of the cylinder head....i made over $200 on that job...yahhh

Aug 01, 2011 | 2001 Mitsubishi Galant

2 Answers

Every time I turn the key to start the motor it blows the 30 amp fuse what is the cause and how do I fix it


if the fuse is blowing when you turn key to start position then this is where to look for the fault ,between the ignition switch and the relay then the other side of the relay to the starter motor solonoid

Mar 05, 2011 | Ford Focus Cars & Trucks

1 Answer

When key is turned to on position, keeps blowing 30 amp fuse


It sounds like you have a short in some wiresets. Check the wires directly connected to the ignition. If this persists, without any problems with wires, I suggest checking the amperage and voltage on your battery to make sure they are at operational levels. Anything over 14.8 volts and you start to fry electrical components and... blow fuses.

Mar 19, 2010 | 1995 Toyota Corolla

1 Answer

2000 Grand Voyager blowing the ignition fuse


Was the old fuel pump bad? It might be worth the cost to replace the ignition switch. The wires to the fuel pump would be a second guess if the old pump was bad and burnt the wires before the fuse went. When you eliminated the fuel pump you also eliminated the wires to the pump and it started. Then you replaced the pump, but not the wires. The ignition switch is the other end of the circuit.

Jun 08, 2009 | 2000 Chrysler Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...