Question about Cars & Trucks

Open Question

Igot code 522739-6 when i turn key to start position blows fuse f3

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Psych0Thrash
  • 53 Answers

SOURCE: crank no start

you've got an open wire in your ignition system that's making fuses blow, i had the same thing happen to me check the wire that runs from the starter to the main fuse box and the wire from the battery to the fuse box. It will only be the wires that carry voltage, none of the ground wires should do that

Posted on Aug 19, 2008

  • 399 Answers

SOURCE: 2001 Mercury Mountaineer keeps blowing the PCM power diode (fuse #19)

Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

Posted on Sep 18, 2008

  • 512 Answers

SOURCE: no turn no start. blows the start fuel fuse intermitantly.

experience says the starter is the likely culprit....it has a bad spot in it

Posted on Nov 16, 2008

  • 5501 Answers

SOURCE: 2000 Grand Voyager blowing the ignition fuse

Was the old fuel pump bad? It might be worth the cost to replace the ignition switch. The wires to the fuel pump would be a second guess if the old pump was bad and burnt the wires before the fuse went. When you eliminated the fuel pump you also eliminated the wires to the pump and it started. Then you replaced the pump, but not the wires. The ignition switch is the other end of the circuit.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: My 2002 Sebring keeps blowing the starter fuse?

Mine is doing the same thing. We are getting ready to replace the starter. Hopefully that is the problem. I'll let you know how it turns out.

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

There is no reaction when turning the key to start the car


Turn key to On.
Turn on headlights manually... Do they come on?
Are there any lights on the dash?
If yes to these, battery is possibly not the sole problem.
Check for good, tight and clean connections at battery terminal posts!
If yes to above, continue on & get a helper... Turn key past on, to Start position.
Do you hear a click sound at time key is turned to Start?
If yes, then ignition switch is not problem, starter relay is getting power, and is now sending power to starter, but starter is not working.
Pic any No's... Then look there.
Good luck.

Mar 29, 2015 | 2005 Ford Focus 1.6

1 Answer

I have a 2005 land rover freelander in the engine fuse box the f3 fuse keeps blowing 15amp you start the truck go down the road fuse blows it starts runing ruff stop turn off truck then try to start wont...


15 amp is a fair current draw and for it to blow after a few minutes means that there is a short in that circuit that is allowing a drain to earth that just exceeds the 15 amp. It is in the ignition part of the system and may be a bad connection ( water ) or a problem appearing in the ECM or relay . Run fault codes to find the area of the fault. Because it is taking time to blow the fuse, it will be difficult to find. Check all wiring for rub marks .

May 07, 2014 | 2005 Land Rover Freelander

1 Answer

K2500 Suburban with. 6.5 Diesel and the instrument fuse keeps blowing when I turn the key to the on position. When I disconnected the glow plug relay the fuse did not blow. Also while running with th


did u replace the relay just a curious question, sometimes they have rust and water in the inside of the relay but my guess would be that you have a bare wire rubbing somewhere, causing the fuse to blow, anything significant has happened before that issue?

Nov 25, 2013 | 1997 Chevrolet Suburban

2 Answers

20 amp fuse keeps blowing engine won't start, fuse


I am a mechanic,i had that same problem where my engine 20amp fuse were blowing....i fixed it...problem were a broken wire in the harnace on the side of the cylinder head....i made over $200 on that job...yahhh

Aug 01, 2011 | 2001 Mitsubishi Galant

2 Answers

Every time I turn the key to start the motor it blows the 30 amp fuse what is the cause and how do I fix it


if the fuse is blowing when you turn key to start position then this is where to look for the fault ,between the ignition switch and the relay then the other side of the relay to the starter motor solonoid

Mar 05, 2011 | Ford Focus Cars & Trucks

1 Answer

I have a 1986 Corvette that blows the 10amp fuse for the fuel pump. How can I determine the cause?


If the fuse blows after turning the ignition key to the "on" position you might try disconnecting the electrical connector to the fuel pump and turning the key to the "on" position. If the fuse still blows there is a short in the wiring to the fuel pump. If the fuse does not blow it is more than likely the fuel pump.

Jan 27, 2011 | 1986 Chevrolet Corvette

1 Answer

When key is turned to on position, keeps blowing 30 amp fuse


It sounds like you have a short in some wiresets. Check the wires directly connected to the ignition. If this persists, without any problems with wires, I suggest checking the amperage and voltage on your battery to make sure they are at operational levels. Anything over 14.8 volts and you start to fry electrical components and... blow fuses.

Mar 19, 2010 | 1995 Toyota Corolla

1 Answer

When i turn my key to the start position the ignition start/run fuse blows. 2004 ram 1500 3.7 engine


probably a bad starter solenoid, first remove the negative battery cable, then remove the two wires from your starter, wrap them in black tape so they wont short out on anything, repl,ace your fuse and hook battery back up and turn key to start, no blown fuse-bad starter, if it blows the fuse it's a wiring short and you should take it to a qualified mechanic

Nov 24, 2009 | 2004 Dodge Ram 1500

1 Answer

2000 Grand Voyager blowing the ignition fuse


Was the old fuel pump bad? It might be worth the cost to replace the ignition switch. The wires to the fuel pump would be a second guess if the old pump was bad and burnt the wires before the fuse went. When you eliminated the fuel pump you also eliminated the wires to the pump and it started. Then you replaced the pump, but not the wires. The ignition switch is the other end of the circuit.

Jun 08, 2009 | 2000 Chrysler Grand Voyager

1 Answer

30 amp ignition fuse in engine compartment blows at start


It sounds like a bad ignition switch or something is grounding out.Try to isolate the problem to key positions.See if the fuse blows when you turn the key to ACC(when your dash lights come on without starting)If the fuse does not blow then when you go to start it and it blows it could be one of many problems,the more common ones could be ignition switch,wiring,starter relay,starter soleniod,or perhaps the starter itself is shorting out,this can sometimes happen when a starter goes bad.

Apr 12, 2009 | 1996 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...