Question about Jeep Cars & Trucks

Open Question

How do I remove oil pan on a 2007 Jeep Commander

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: location of oil dipstick

The oil dipstick is located at the back of the engine.  If you look at the engine from a top view it is located at about 11 o'clock.  It's black.

Posted on Dec 22, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: 2003 oil pan removal

4.0L Engine To Remove:

  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Posted on Jun 06, 2009

joecoolvette
  • 5660 Answers

SOURCE: 2007 Jeep Commander will not start

Check the battery cables, then go to the starter relay, then the starter, (If the lights are bright when you turn them on)

Posted on Aug 01, 2009

BCally1
  • 133 Answers

SOURCE: 2007 jeep commander rocky mountain no sound from radio

take it to the dealer. they will put a new radio in it if you have under 36000 miles

Posted on Sep 12, 2009

  • 17 Answers

SOURCE: how to change the time on a 2007 jeep commander.

There should be a button says " TIME" or "Set Up" and make your selection by turning the right knob.

Posted on Oct 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the 3rd row headrests from a 2007 Jeep Commander?


Their held in with a snap ring or look at where they mount to the seat. If you see screws/bolts, take them out. If not you will have to pry/pop them out.

Nov 30, 2014 | 2007 Jeep Commander 3.0

1 Answer

How do i remove engine oil pan on 2006 jeep commander 4.7


ALWAYS, ALWAYS, ALWAYS.......CONSULT A SHOP MANUAL!
YOU MAY HAVE TO REMOVE UNDER ENGINE SUPPORT COMPONENTS, EXHAUST, ++...OR IT MAY JUST UNBOLT AND DROP DOWN

Nov 24, 2014 | Jeep Cars & Trucks

1 Answer

What are the torque specs for the transmission pan bolts?


i posted this 2 time this week.

no trans model stated.
one is 70 INCH POUNDS
and other is 100.
why not learn what driveline is on car first, then ask questions.?
ill list 2 here

45RFE
or NAG1

learn that, and we can answer
better , you learn it the learn to use GOOGLE
example
" Jeep 45RFE pan torque"

eg
https://www.google.com/webhp?gws_rd=ssl#q=+Jeep+45RFE++pan+torque


easy huh , lots of others asking the same question, with no FSM
in the shop.

Oct 04, 2014 | 2010 Jeep Commander 3.7

1 Answer

How do I remove/replace driver door wiring harness from my 2007 jeep commander?


I dont know the specifics of your Jeep but on most cars there are alot of harness connector plugs behind the plastic kick panels under the dash-ahead of the doors

May 08, 2014 | 2007 Jeep Commander 4.7

1 Answer

How to remove 2007 jeep commander climate control panel for light bulb replacement


The lights in the climate control panel are not bulbs, they are LED and the entire panel will need to be replaced. I would check for a bad connection before replacing the panel assembly.

Dec 28, 2010 | 2006 Jeep Commander

1 Answer

Transmission gasket leaking


Remove pan and change the gasket. While youre doing that if its been a while you already have the pan off why not change the tranny filter too, it just pops off and new one pops in. Fill with new tranny fluid, let it warm up and make sure the oil is in the cross hatched area on the dipstick when idling in park and tranny is warm

Dec 01, 2010 | 2006 Jeep Commander

1 Answer

The driver side rear seat of our 2007 Jeep Commander will not release and fold down. How to manually dismantle or release and fold down?


Our 2006 just had the second one go stuck up when this happens the folding up gears are in the wrong engagement must remove trim to expose gear and spring to reset proper quite involved

Jun 13, 2010 | 2007 Jeep Commander Rocky Mountain

1 Answer

Oil pan removal 3.7


a lot tougher job than in the old days!

The engine oil pan is made of laminated steel and has a single plane sealing surface. The sandwich style oil pan gasket has an integrated windage tray and steel carrier. The sealing area of the gasket is molded with rubber and is designed to be reused as long as the gasket is not cut, torn or ripped

1.) Disconnect negative battery cable.
2.) Remove the radiator fan
3.) Remove the intake manifold you need to do this to install the engine support tool
4.) Install engine support Tool #8534 Do not raise engine at this time but make sure it is tight!
5.) Remove the structural cover
6.) Remove both left and right side engine mount through bolts
7.) Raise engine to provide clearance to remove oil pan.
8.) Drain engine oil and remove oil filter
9.) Remove the oil pan mounting bolts and oil pan.
10.) Unbolt oil pump pickup tube and remove tube and oil pan gasket from engine.

NOTE:Do not pry on oil pan or oil pan gasket. Gasket is mounted to engine and does not come out with oil pan.



reverse to install
do not over tighten bolts
follow normal torque sequence but here's a pic just in case
eabea73.gif


Apr 05, 2010 | 2006 Jeep Commander

1 Answer

2007 jeep commander rocky mountain no sound from radio


take it to the dealer. they will put a new radio in it if you have under 36000 miles

Sep 02, 2009 | 2007 Jeep Commander Rocky Mountain

1 Answer

Can't locate air filter...


1. Loosen clamp (1) and disconnect air duct at air cleaner cover (3). 2. Pry over 4 spring clips (5) from housing cover (spring clips retain cover to housing). 3. Release housing cover (3) from locating tabs on housing and remove cover (3). 4. Remove air cleaner element (filter) from housing.
cecdf0c.jpg

Jun 30, 2009 | 2007 Jeep Commander Rocky Mountain

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...