Question about Cars & Trucks

Open Question

Bleeding the 3.6 ly7 v6 cooling system - Cars & Trucks

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76673 Answers

SOURCE: i was bleeding the cool system on my 2001 olkwagon passat v6 and i realized that one of my bleed hole of the rear was leaking fluid what should i do?? help!!

Take the bleeder out, take it with you and go find a like sized brass pipe plug from the auto parts store. Try NAPA auto parts or Carquest, they have the best selection of this kind of stuff

Posted on Sep 14, 2012

Ad
  • 760 Answers

SOURCE: How to bleed the cooling system on a 01 Ford Taurus V6 24 valve

all you have to do is run the engine after filling the coolant bottle to the cold fill mark just start the engine and let it run with the cap off the level will go down and then add more antifreeze The coolant circulates and gradually vents air out when it expands put the cap on and drive the car the next day check the level if you need it add more when the engine is cold to the cold full mark on the bottle that's it this is a simple thing that's done by running the engine have fun and good luck Stephen if for some reason your having some other problem post back we're all here to help you put hey Stephen and I'll see it o.k. -------later man!

Posted on Feb 22, 2015

  • 12182 Answers

SOURCE: how do you bleed the air from the cooling system of a 1999 v6 pontiac grand am

Refilling Procedure




Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL?"¢ coolant. If coolant other than DEX-COOL?"¢ is added to the system, the engine coolant will require change sooner: at 50 000 km (30,000 miles) or 24 months.






  1. Close the radiator drain cock.


  2. If previously removed, install the engine block drain plugs.


  3. When installing the drain plugs, use pipe sealer GM P/N 12346004.




    Important: On vehicles equipped with the 3.4L engine, open the coolant air bleed valve. The coolant air bleed valve is located on the top of the thermostat bypass pipe/heater pipe assembly. Close the valve once a continuous stream of coolant is expelled from the valve.



  4. Fill the surge tank to the base of the filler neck.


  5. Start the engine with the pressure cap off. Run the engine until the upper radiator hose starts to get hot.


  6. If the coolant level in the surge tank is low, add the proper mix of coolant until the level reaches the full cold line.



  7. Important: After servicing the cooling system, and if the vehicle is equipped with an intermittent low coolant light, an occasional low coolant light may be encountered during some extreme driving maneuvers. This complaint should be eliminated by removing the surge tank cap and adding coolant to a level just at or above the full cold line when the system is cold.



  8. Install the cap onto the tank with hand tight pressure.



Recycling Procedure




Important: Dispose of used coolant in a proper fashion, such as in a used coolant holding tank. Never pour used coolant down the drain. Ethylene glycol antifreeze is a very toxic chemical. Disposing of ethylene glycol antifreeze into the sewer system is both illegal and ecologically unsound.



There is currently no approved method for recycling used DEX-COOL?"¢ coolant into new DEX-COOL?"¢ coolant. DEX-COOL?"¢ coolant can be recycled into new conventional coolant. Consult local listings for coolant recycling facilities in your area.

Posted on Dec 31, 2015

  • 583 Answers

SOURCE: How to bleed air from 2010 Mazda 5 2.3 L cooling system?

I always park on a slight incline with engine cool...start with radiator cap off and air should travel to radiator and out

Posted on Sep 16, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding the coolant system 2005 chevy uplander


Bleeding the coolant system Leisa, Check the attached links,instruction and guides on bleeding cooling systems. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Fill Bleed Coolant Chevy 3 4L V6
Bleeding Air In Cooling System
Coolant Flush How to Chevrolet Uplander 2005 2008 2008 Chevrolet Uplander...
How To Bleed Cooling System EricTheCarGuy


May 21, 2016 | Cars & Trucks

1 Answer

Where is the knock sensor located on a 2004 Cadillac srx v6 engine 3.6L


No sir, on the ly7 HFV6 3.6l in the 04-09 srx and cts the knock sensors are located on the sides of the engine block. Bank 1 and two are visible fringe wheel well. Not to hard to get to with a 3/8 drive 13mm socket, universal joint, and short extension. I would also check the connector with a multi meter while doing this job to ensure you have a good connection and harness is not damaged. Best of luck!

Mar 31, 2015 | 2004 Cadillac SRX

1 Answer

How to bleed the radiator on a peugeot 2006 307 XS model


B1GG0RK1 - 206 TU ENGINE DW8 ENGINE
DRAINING - FILLING - BLEEDING COOLING SYSTEM
1 - SPECIAL TOOLS
b1gk06lc.gif[1] filling cylinder (-).0173/2 .
2 - DRAINING
TU ENGINE
b1gk070c.gifDW8 ENGINE
b1gk073c.gifALL MODELS
Carefully remove the expansion chamber cap .
b1gk06kc.gifUnscrew the radiator drain plug (1) .
NOTE : fit a pipe to the outlet to allow clean drainage of the system .
TU ENGINE
b1gk071c.gifDW8 ENGINE
b1gk074c.gifALL MODELS
Open the bleed screws (2) .
DW8 ENGINE
b1gk075c.gifDrain the engine by removing the plug (3) .
ALL MODELS
3 - FILLING AND BLEEDING THE SYSTEM
Before any re-filling operation, flush the cooling circuit with clean water .
WARNING : check the cooling system for leaks .
DW8 ENGINE
b1gk076c.gifTU ENGINE
b1gk072c.gifALL MODELS
Fit the filling cylinder [1] to the filler opening .
Open all the bleed screws .
Fill the circuit slowly with coolant .
Close the bleed screws in the order in which the liquid flows without bubbles .
The filling cylinder must be filled to the 1 litre mark to bleed the heater matrix correctly .
Start the engine .
Maintain the engine speed at 1500 to 2000 rpm until the end of the second cooling cycle (fan(s) starting then stopping) keeping the filling cylinder filled to the 1 litre mark .
Stop the engine .
Remove the filling cylinder [1] .
Immediately tighten the plug on the expansion chamber .
If necessary fill up to the level of the maximum mark (Engine cold) .

Jul 06, 2014 | Cars & Trucks

1 Answer

I have no heat in my car, it's an audi a6 1996 2,6l v6. I thaugt it was air in the cooling system, but i've been bleeding the system for 3 hours.. At the first i used the air screw at the drivers side in...


You likely have issue with the air temperature blend door, either the door is jammed (common) or the actuator is defective, but that is most often caused by the sticking blebd door, it is plastic and warpin is common.

Mar 17, 2014 | Audi Cars & Trucks

1 Answer

2003 pontiac grand am bleeding the cooling system


Look on your exhaust manifold. What you are looking for is a little bleed screw. Mine is painted blue. Yours maybe a different color. When you find it start your engine and let it idle for 3-5 minutes. Make sure your heat is turned on full. With the enging running turn bleed screw counterclockwise till water starts shooting out. Let the water continue to shoot out until you get a steady stream. Once you get that steady stream then tighten. Your system is now bled.

Dec 30, 2013 | 2003 Pontiac Grand Am

1 Answer

I was bleeding the cool system on my 2001 olkwagon passat v6 and i realized that one of my bleed hole of the rear was leaking fluid what should i do?? help!!


Take the bleeder out, take it with you and go find a like sized brass pipe plug from the auto parts store. Try NAPA auto parts or Carquest, they have the best selection of this kind of stuff

Sep 14, 2012 | Volkswagen Passat Cars & Trucks

1 Answer

Cooling system needs bleeding xedos 6 v6.20 where is bleed nipple


There is no bleed nipple in a cooling system. You'll need a vacuum pump and the proper adapter for the radiator.

May 10, 2011 | 1995 Mazda MX-3

2 Answers

No visible leaks in cooling system but engine overheats. 2004 Ford Explorer 4.0L V6. Fan working fine. Any suggestions.


#1.airlock in system....undo a heater hose clip to bleed.#2 thermostat jammed..replace.#3..water pump shot..replace.#4..radiator clogged..backward flush the system..

Oct 15, 2010 | 2004 Ford Explorer

2 Answers

93 Camero v6 engine


The cooling system could have air in it and need bleeding.I would suggest a pressure test on the system.If you are sure that it has to much pressure.I would suggest a compression test to eliminate blown head gaskets or cracked or warped heads.Also check you intake gaskets.Good Luck!!!!!

Aug 03, 2008 | 1993 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...