Question about Dodge Caravan
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Alright, here's a pic of the mechanicals:
The bad news is on your vechile you have to remove the timing belt, but here's a step by step.
The timing belt can be inspected by removing the upper (front outer) timing cover.
Posted on Jun 28, 2008
JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.
GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.
Posted on Apr 29, 2009
It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket
Posted on Jun 02, 2009
Make sure it's cool, pop the radiator cap, Remove the shield on the passenger side between the tire and front of engine. Relieve the tension on the serp belt,draw yourself a diagram of the pulleys and belt routing in case the sticker is gone on the strut tower, remove the serp belt. Take the bolts out of the pulley on the front of the water pump (3). Remove the lower radiator hose at the front cover to drain the coolant. Remove the 6 mm bolts holding the water pump to the front cover housing. tap on the pump with a rubber hammer. Install a new gasket on the new pump, and a weap hole diverter in the pump (round black about hte size of a quarter), use old one if there's no new one. Install pupm and tighten bolts snug with a 1/4" ratchet. Install pulley and 3 bolts. Install belt, top off radiator with 50/50 mix green coolant. start engine and run to operating temperature,make sure the belt is seated in all of the pulleys and is running true, radiator fans should come on. Shut engine down and let cool overnight. Check level in radiator and overflow bottle, top off as necessary.
Posted on Aug 26, 2009
Try (repairpal.com) for estimate for your particular area. You may have to enter Grand Caravan to get the 3.8L engine .
I'm thinking 2 hrs.
Posted on Oct 05, 2009
Tips for a great answer:
Sep 02, 2011 | 2000 Dodge Caravan
Dec 08, 2010 | 2004 Dodge Caravan
Nov 18, 2010 | 2000 Dodge Caravan
May 06, 2010 | 2001 Dodge Caravan
Nov 28, 2009 | 2001 Dodge Caravan
Oct 05, 2009 | 2005 Dodge Caravan
Sep 29, 2009 | 2005 Ford F-150
Oct 24, 2008 | 1993 Dodge Caravan
Jun 16, 2008 | 2000 Dodge Caravan
Jan 15, 2018 | Dodge Cars & Trucks
34 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: