Question about 2000 Chrysler LHS

Open Question

Where to replace the combo flasher on the Chrysler LHS 2000

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

localwonder
  • 6784 Answers

SOURCE: how do you replace the headlight bulb on a 2001 chrysler lhs.

This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Posted on Jan 28, 2009

bunnydawg
  • 5158 Answers

SOURCE: where is the starter on a 2000 chrysler lhs?

I can't tell you what side it's on.... but it is where the motor joins to the transmission. if it is front wheel drive (the motor is sideways). look down about the middle of the engine where it joins the transmission.... that is your starter. you should be able to follow one of the large wires from the battery to it. speaking of which make sure you disconnect the battery before changing the starter.

Posted on Apr 15, 2009

  • 1 Answer

SOURCE: replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?

I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Posted on Apr 15, 2009

CMV9
  • 594 Answers

SOURCE: HOW TO REPLACE HEADLIGHTS ON

ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Posted on Apr 16, 2009

  • 6 Answers

SOURCE: I need to replace the

Hi, I believe there is a tensioner that is situated below the alternator and have to loosen up gradualy and then you belt will come off the crank/water pump/alternator and then remove the a/c compressor belt, and also if you don't need to run your a/c or you dont want to chang the compressor you don't need that belt, your vehicule will run fine, that belt run only you a/c compressor Mike

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a turn signal relay on a 2000 Chrysler Concorde


The Combination Flasher, also referred to as the combo-flasher, is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in a rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification.
The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher). The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.

Ref: http://www.10w40.com/questions/auto-repair-questions/where-is-the-flasher-relay-on-a-2000-chrysler-concorde
Good Luck

Mar 03, 2015 | 2000 Chrysler Concorde

1 Answer

How do I change the flasher fuses


Flashers have no fuses.. they are either electronic or thermoelectric in their operation. They either work or fail completely. If they don't work you unplug them and plug in another one.. The clicking sound is to alert you to their working and remind you the lights are blinking

Feb 12, 2015 | 2000 Chrysler LHS

1 Answer

Do you know where i am suppose to replace the flasher fuse on a chrysler lhs 1999


The flasher is located under the drivers side dash... Look to the left of the steering column area. If you have purchased a replacement, then just look for a similar looking flasher. Best of Luck!

Aug 20, 2011 | 1999 Chrysler LHS

1 Answer

Turn signals/hazards not working on my chrysler lhs 1999 I changed fuses and flasher still no luck not even lightning up on the dash


if you have power when key is on for turn signals on both sides of the fuse,you will probably need to replace the multi function switch

Dec 03, 2009 | 1999 Chrysler LHS

1 Answer

Turn signals in96 LHS chrysler won't work


did you replace flasher solenoid, see if the emergency flashers work all around vehicle, if not then replace bulb that does not flash

Jul 30, 2009 | 1995 Chrysler LHS

1 Answer

Blinker and flasher does not work


you might want to see if there is a flasher relay on you car a auto parts store can tell you they are cheap around 8 to 25 dollars i would start there first if they are not flashing

Jun 25, 2009 | 2000 Chrysler LHS

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Apr 15, 2009 | 2000 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

Not finding what you are looking for?
2000 Chrysler LHS Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...