Question about 2000 Chevrolet Cavalier

Open Question

How do i program my key fob on my 2000 cavalier using diagnostic tool 3100g

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: hand held diagnostic tool

OK...
If the scann tool is powered with the power of the Vehicle.
It's mean the connector is missing a power .
To fix this you need to check. the following
Check the " CIG" fuse 15amp. This fuse give +12 v to the cigarret lighter and OBDII diagnostic connector.
Is the Orange Wire of the OBDII connector and PIN # 16
The Ground is the PIN # 4, black wire, and PIN # 5, black/white.
Be sure of this wires are correct fix if any need,
after try to sacn again or see if there a power when you connect the Scann tool.

OK.. I hope this help to try diagnostic your vehicle,
Thank you for use fixya.

any further info, let me know.

Posted on Aug 13, 2008

jagjeffery
  • 316 Answers

SOURCE: programming used key fob for a 2000 tahoe

get in your truck close all the doors put your key in the ignition push and hold your unlock button on the door panel turn the key on then off then on then off release the onlock button at this time the lock should cycle lock then unlock by them self if they did push and hold your lock and the unlock buttons on your remote at the same time for 15 seconds the lock should cycle agian and you are programmed

Posted on Jun 04, 2009

emissionwiz
  • 75051 Answers

SOURCE: Need to re-program 2000 Chev.C3500 key fob need help

1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Posted on Jun 09, 2009

rogrrabbit
  • 986 Answers

SOURCE: how to program key fob. I have the fobs.

Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Posted on Jun 25, 2009

emissionwiz
  • 75051 Answers

SOURCE: trying to program my key fob - how do I install a

I can help, but need the model and year of the car

Posted on Oct 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 trailblazer and i bought a fob and it does not work after programing Everything thing works on my truck but the fob. Any ideas?


How was it programmed ? Was a scan tool used ?
Program All Key Fobs
To complete this programming operation, all keyless entry transmitters associated with the vehicle must be available for programming. Once placed into program mode, all previously programmed transmitters will be erased from memory upon the receipt of the programming signal from the first transmitter.
  1. Close the lift gate.
  2. Ignition ON, access the scan tool Lift gate Module Setup menu and select Program All Key Fobs.
  3. Follow the scan tool on screen instructions in order to program the transmitters. Select "Start" on the scan tool to enter the program mode.
  4. As each transmitter is successfully programmed, the scan tool will show how many transmitters have been placed into memory.
  5. When all transmitters are programmed, exit the program mode by selecting "Stop" on the scan tool. The vehicle will not respond to the transmitters until the program mode is exited.
  6. Operate the transmitter functions in order to verify correct system operation.
Program Individual Key Fob
If there are less than four keyless entry transmitters programmed to the vehicle, an individual fob transmitter can be added. This method will not erase previously programmed transmitters from memory.
  1. Close the lift gate.
  2. Ignition ON, access the scan tool Lift gate Module Setup menu and select Program Individual Key Fob.
  3. Select "Program additional Key Fob" on the scan tool.
  4. Follow the scan tool on screen instructions in order to program the transmitter.
  5. Operate the transmitter functions in order to verify correct system operation.

Apr 08, 2016 | Cars & Trucks

1 Answer

How do I program my remote key fob for a 2007 pontiac grand prix?


Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

Nov 05, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

How do I program a new key fob for a 2007 Grand Prix? Bought a replacement on e-bay.


Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

Nov 05, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

1 Answer

My key starts the car but the locks will not activate using the fob buttons and the indicators no longer flash even when i use the key to lock the car


Programming
When
Key(s) added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. Turn ignition switch from position I to position II 4 times within 6 seconds. Turn ignition switch to position I ( 11/2000). Switch ignition OFF (12/2000 ). Programming mode activated for 10 seconds proceed as follows: Press and hold lock, unlock or boot release button Fig. 1 [1], [2] or [3]. Wait for acoustic signal (indicates correct programming). Repeat above procedure within 10 seconds to program remaining keys. To exit programming mode: Turn ignition switch to position III or wait 10 seconds. Keys can also be programmed using diagnostic equipment.


NOTE: A maximum of 4 keys can be programmed

Nov 19, 2010 | 2002 Ford SVT Focus

1 Answer

Keyless entry remote programming


Hello here is the instructions for programming the key fobs

This procedure will add, replace, or invalidate all key fobs. This procedure requires that you have a known good key fob available, a new/replacement key fob, the vehicles mechanical key, and a scan tool.
Method 1 is also used for the initial programming of fobs to a new replacement RCDLR. In this instance, the new RCDLR comes ready to learn the first key fobs introduced. Perform the learn procedure as outlined, with the exception that the new RCDLR does not require a known good key fob be placed within the interior of the vehicle.
Note: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Methods 2 or 3 must be used in this instance.
  1. The vehicle must be OFF.
  2. Place a known key fob and any new/replacement key fob(s) to be programmed in the cupholder inside the vehicle. DO NOT place any fobs in the console fob pocket at this time.
  3. Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
  4. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4). → If the DIC displays: OFF/ACC TO LEARN, the known fob has not been recognized. At this time, programming will revert to Method 2.
  5. If the DIC is displaying the correct fob number that needs to be programmed, skip ahead to step 9.
  6. If the DIC is not displaying the correct fob number that needs to be changed (i.e., the DIC is displaying: READY FOR FOB 3, and you wish to program FOB 1), use the scan tool to access the following: • Vehicle Control Systems • Computer/Integrating Systems • Module Setup • Remote Control Door Lock Receiver • Program Key Fobs
  7. Select the fob position you wish to program: Note: Selecting Invalidate All Fobs will erase any known fobs and will cause the DIC to prompt READY FOR FOB 1, requiring all fobs to be relearned to the vehicle.
    • Invalidate All Fobs • Program Fob 1 • Program Fob 2 • Program Fob 3 • Program Fob 4
  8. With the fob position selected, press the PROGRAM soft key on the scan tool. The DIC should display: READY FOR FOB X (X = fob 1, 2, 3 or 4, depending on the selected position)
  9. With the DIC displaying the correct fob position that is to be programmed, place the new/replacement key fob in the console fob pocket with the buttons facing forward.
  10. A beep will occur once the fob has been learned.
  11. If programming additional key fobs and there is no DIC prompt that indicates READY FOR FOB X, repeat steps 7 and 8.
  12. Exit programming mode by pushing the OFF/ACC portion of the ignition switch. Note: Failure to exit programming mode (press OFF/ACC) prior to pressing the UNLOCK button of each key fob programmed will result in that fob being inoperative. Pressing the UNLOCK button completes the programming sequence and is require to ensure transmitter operation.
  13. Press the UNLOCK button on each key fob that was programmed to finalize the programming and confirm system operation.

Nov 03, 2010 | 2006 Cadillac STS

1 Answer

Key fob wont unlock door or switch off alarm on my coupe


Take the vehicle into a Hyundai Service Center (dealership), pay the diagnostic fee. They can program your key fobs.

Jul 12, 2009 | 2000 Hyundai Accent

1 Answer

Programming a key fob


you will need the dealership diagnostic tool to program the remote

Apr 24, 2009 | 2003 Chrysler Town & Country

2 Answers

Programming a 2006 Pontiac Gran Prix Keyless remote


The rke on 06 pontiac only can be programed using a diagnostic scan tool or Tech 2.
Conect the scan tool to the vehicle. turn key to on position.
Select 1 body, 2 them select special funtions
3 slect program key fob,
4 select the number of key fob you want to program.
5 Press and hold the lock and unlock key simultaneous. about 15 seconds
The power lock cycle confirm the remote is programed.

Jul 03, 2008 | 2006 Pontiac Grand Prix

Not finding what you are looking for?
2000 Chevrolet Cavalier Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...