Question about Cars & Trucks

Open Question

Where can I buy a replacement coil sprung back axle (Omega type) for my classic Panda

Posted by on

  • David Ellis Rhea Apr 18, 2017

    Hi Buz Busbridge, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Try a Fiat dealer, or ask them where Fiat junk yards are to be found.



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replacement part for krups F417

go google and type in -- krups k417 -- and there are pages of information from different sites

Nov 14, 2015 | Cars & Trucks

1 Answer

How do I remove the rear end axle on a 1995 poly traction police issued caprice classic

First off I think you mean Posi-traction which means both axles turn with power to the wheels. You remove the axle grease from the rear end draining it then you remove the cover try and do it slowly so that you don't make getting the old gasket off really hard after cover is off you will see the rear end look inside at the pinion gears the axle goes through them you will see how they are held on just remove the pins when putting back together use some axle grease on the splined ends and make sure that the housing and the cover is really clean so that the gasket seals properly ,nothing worse than rear end oil leaking.

Apr 20, 2015 | 1995 Chevrolet Caprice Classic

1 Answer

Spring broke on back axle

Hi Lenard
Its jsut like those front coil springs on all the older cars had with a shock going up threw it.... ist coil design and about 16 inches in height yours is all by itself on the rear axle go to muffler shop they do shocks and springs cheapest way. Just remember if you replace one only side your car might be higher on new side of coli replaced,, its kinda like buys shoes dont just buy one but the pair

Oct 09, 2012 | 1993 Buick Regal

1 Answer

I was about to help a lady friend change the oil filter on a Fiat Panda 1100cc petrol engine but on lifting the bonnet I could not locate it. I checked with the Car hand book which made no reference to its...

did you ever find the location of the oil filter? a local auto shop sold me a filter for my wifes Panda 1.1l active. However, when it came time to do the oil change I found myself searching the internet for answers also.

William G.

May 23, 2010 | 2007 Fiat Pininfarina

1 Answer

Can i fit a freelander engine and axles to my series 3

in a word no the freelander is a uni body construction,and most freelander owners would prefer to go for the defender set up not the other way round, you would be better of looking at coil sprung hi breed kits for your s3 and maybe a mitsubshi diesel for economy.

Dec 12, 2009 | 2002 Land Rover Freelander

1 Answer

Squeeky rear wheel bearing. How is it removed and replaced?

This is a rear wheel drive vehicle? Are you sure it's not a brake squeal?
The bearing sits in the end of the axle tube and is lubed with the differential fluid. You need to dissasemble the differential to remove the axle, to remove the bearing. You need a puller for that type of bearing.

Sep 08, 2009 | 1994 Chevrolet Caprice Classic

1 Answer

ROLL bar malfuntion. Roll bars will not go down. Is there a reset button?

This system is designed to release the roll bar from the actuating rams due to input from the axle(suspension travel) sensors in the rear of your vehicle. More than likely your roll bar system released the bar and it sprung upwards. You have to hold the roll bar switch in the up position until the rams travel up and lock back into the bar. Once they lock back in the system will be operational again.

Jun 27, 2009 | 2000 Mercedes-Benz CLK

3 Answers


Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Apr 28, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Door sensor controls

How could you damage the transmission and axles after only 80k miles? If you do some work yourself, all the other stuff is cheap to fix.

Aug 13, 2017 | 2003 Volkswagen Jetta TDI

1 Answer

The left rear wheel is towed out

The car as it is would not be safe, even if you find a temporary adjustment for the axle, that had probably been deformed or broken by the shock.
In your situation you need to have the car inspected by a qualified mechanic, and the axle eventually replaced.


Jun 22, 2008 | 2008 Suzuki SX4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides