Question about Cars & Trucks

1 Answer

1998 windstar ecm not sending codes - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 12,158 Answers

Maybe it has none to send !

Posted on Apr 18, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

2001 windstar im getting codes po172 po174 po301 po302 po 303 po304 po300 installed new coil pack twice new wires,plugs,cam and crank sensors,fuel andair filters,pcv valve and now get these codes. ...


Get your ECM replaced. Usually it's next to battery or inside front fenders. The rain must have shorted out connections and fried ECM. Engine will sputter until it is done. Usually autozone, advance auto, or dealer has ECM.

Apr 14, 2014 | 2001 Ford Windstar

2 Answers

How to flash ecm on 1998 windstar


need to take it to the dealer to be reflashed around 100 dollars

Oct 26, 2012 | 1998 Ford Windstar

1 Answer

ABS light on a 1998 chrysler cirrus comes on only after the doors lock when driving down the street,why?


This is the short story.The transmission sends a signal to the ECM that sends a signal to the BCM (This is what locks the doors) The ECM also sends that signal to the ABS. When the ABS doesn't sense a signal from the wheel sensors, the ABS light comes on. Have the codes checked. Let me know. Randy

Sep 26, 2011 | 1998 Chrysler Cirrus

1 Answer

Why is it that once the speed meter stops reading,it affects the speed of the car and gear selection


It is because the speedometer is run off the wheel/ speed sensors. threw the ABS module. Which in turn sends the signal to the ecm, that runs all the other sensors and actuators. When the ECM doesn't sense any speed it thinks the vehicle is stopped, or in park. So it runs the engine a certain way. I had a 200 windstar and worked on several others that the exciter ring on the cv axles split. This caused an intermittant speedometer lose. I pushed the exciter ring back in place and spot welded in a couple of places and never had any problems afterwards. If this is your problem , you don't have to worry about the gap in the ring, when you get it back on.

May 11, 2011 | 1998 Ford Windstar

1 Answer

1998 Windstar--My fuel pump is working, and I am getting gas up to the fuel rail, but my injectors are not working.


Check Fuses All Of Them Under Hood, Dash ect...., Check Fuseable Links Make Sure Check Engine Light on dashboard is on ....Probe ECM For Answers like Cam Sensor,Crank Sensor ect...just example...but i would probe ECM Memory for answers..hope this helps

Jun 18, 2010 | 1998 Ford Windstar

1 Answer

Where is oil pressure sending unit?


lower right hand side, front of engine, below the power steering bracket.

Nov 07, 2009 | 1998 Ford Windstar

2 Answers

I have a 98 ford windstar with a 3.8, that has an engine miss and two dtc's po401 and po402, would a bad EGR valve cause this miss?


HI you maybe having this codes and engine missing because of a plug up catalytic converter have it tested at your muffler shop

Sep 25, 2009 | 1998 Ford Windstar

1 Answer

Just change the ecm on my 2001 ford Windstar and it won't start the anti theft light is blinking


did you get the ecm flash programmed? newer vehicles require the ecm to be flash programmed before they are installed your dealer and some auto parts stores can do this for you it usually runs around $90.

Mar 20, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...