Question about Ford Cars & Trucks

2 Answers

1995 ford 5.0 oil pressure problem no oil pressure till 20-30 seconds after statup but then fine

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,717 Answers

If its not tappin or hammering it's probably just the sender. If it is it could be the pump or bottom end bearings.

Posted on Apr 18, 2017

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 219 Answers

Try changing your filter it may be dirty. Also chk your oil viscosity. Try 30 wght.

Posted on Apr 18, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0449 code 1995 dodge dakota


2ec21afa-b94b-4fb4-8163-08305765a931.gif
(1)EVAP Purge Solenoid Ignition Positive Voltage
(2)To Intake Manifold Port
(3)Fuel Tank Pressure Sensor
(4)Fuel Tank Pressure Sensor Ground Circuit
(5)Fuel Tank Pressure Sensor Signal Circuit
(6)Fuel Tank Pressure Sensor 5V Reference Circuit
(7)Fuel Filler Neck
(8)Rollover Valve
(9)Fuel Tank
(10)EVAP Vent Valve
(11)EVAP Vent Valve Control Circuit
(12)EVAP Vent Valve Ignition Positive Voltage
(13)EVAP Canister
(14)EVAP Purge Solenoid
(15)EVAP Purge Solenoid Control Circuit

check this out on your vehicle. also make sure there is no air lines leaking on the engine.

Jan 25, 2014 | 1995 Dodge Dakota

1 Answer

I dropped the fuel tank to drain old gas.I put new gas in and turned engine to start it didnt start. Should I be able to hear fuel pump if it is working?This is for a 1990 ford e-150 van.Also where the is...


Turn the key to the ON position without starting the engine. You should hear the fuel pump running for 5 seconds if working. This primes the gas to the injectors when doing this. If not heard running check the oil pressure switch for the 12 volts needed to run the fuel pump starts there on that harness. When the engine starts and the oil pressure reaches the normal pressure the computer shuts off that circuit and turns on the fuel pump relay to run the pump. The relay stays on till you shut the engine off

May 08, 2010 | 1990 Ford Econoline

1 Answer

Oil pressure gauge shows no pressure when its cold out for about 5 minutes till it warms up 97 ford f150/4.6l. I use 10w30 oil, could there be a wire connection to the motor be shorting? where is it? Or is...


Jim, I think your oil pressure sender is going bad, you should replace it and see that your oil pressure is in fact good, you can also check and verify the wires to it at the same time. It is located next to the oil filter. Hope this helps, let me know

Dec 09, 2009 | 1997 Ford F150 Regular Cab

1 Answer

My 1995 ford f150 v8 302 will not start


Ford truck was running fine then it just shut's OFF, afterwards did start once stayed on for a couple of minutes then shut off again. A friend thinks it's the computer after checking the car. Note I did pressure wash the engine 2 day's before and didn't use it till now.

Nov 08, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

I HAVE SAME PROBLEM


Make sure you are using a genuine Ford oil filter. The Ford filter has pressure valves in it to keep the oil where it belongs. Make sure you are using the proper weight of oil.

If the oil and filter are proper, it sounds like the oil pump pickup is clogged or there is excessive play in the crank bearings. The engine is running dry on oil because it is not pumping up until the oil is circulating completely through the engine.

Sep 11, 2009 | 2001 Ford Expedition

2 Answers

95 windstar ( 3.8L )Will not fire.Did start and


Clogged fuel filter maybe or the fuel pump isnt coming on or the injectors are bad.

Jul 28, 2009 | 1995 Ford Windstar

4 Answers

Too much oil in motor, how do i drain the excess oil out of the motor? I have a 1995 chevy lumina 3.1


yourgoing to have to drain it from the pan just pull the drain plug and let it all drain. change the filter and then replace with 5 quarts of 10w30 oil perferably quakerstate or valvoline brand

May 16, 2009 | 1995 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...