Question about Cars & Trucks

1 Answer

Thanks for your answer joney but wots a key hurb is it the key barrel that can take out as I am a novice at this thanks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.

  • Expert
  • 108 Answers

Sorry paul i meant to say the ignition harb go to any place where you can buy parts for your car and tell them you want an ignition harb the part where you put it the key they will give you the whole part its not that expensive its less than R300.00. give them the model and make of the car

Posted on Apr 19, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to change ignicion lock cilinder on a suburban 97 do not turn

strip out the cowling around the ignition , and now you will have to make the barrel turn so the retaining oin can be accessed ' try spraying oil into the ign barrel and GENTLY wiggle the key until it turns , if no joy then will have to force out the whole ignition assembly ,not the sort of job to be done by a novice , worth paying to get it done right

Oct 07, 2014 | Cars & Trucks

1 Answer

How to replace ignition tumbler on 2000 ml320 mercedes benz?

i would assume that there is a hardened steel sleeve "VERY HARD" that surrounds the barrel the same as the W140 model. the repair shop will have trouble cutting this off , like the novices at diesel motors in perth western australia. and will probably want to charge you around $3,000 AUD to replace the key and barrel. which collapsed in my case. jamming the key in the ignition. not bad for a vehicle that had cost $219,000 AUD , and had covered 220,000 km, when there countless thousands of 40 year old toyotas and holdens running around with the original ignition barrels. anyway , digressing , the switch that sits behind the actual barrel lock will no doubt fail not long after u change the barrel also. because i would say that the junk they manufacture for these over rated piles of trash (still riding on the reputation of their 1970's products, is about the same quality level as cheap rubbish componentry used in the W140 . "google search for W140 wiring harness there s a blog with a list of owners in the US with failed wiring insulation causing the copper wires to short out and in many cases cause engine fires. manufactured by Bosch to MB specification to be biodegradable, what a totally brilliant place to start , crucial electronic components, with severely limited life from the start.! , the ignition switch doesn't need to be cut out of the steel dash frame like in earlier models, and is not particularly hard to remove however the stealer will still try to slug u around a grand and tell u its a HUGE job. a friend of mine had my ignition barrel and switch out in 20 minutes after the switch behind the barrel failed after the dealer installed a new key and barrel and charged me 6 hours or so at $120/ hour.

Sep 13, 2013 | Cars & Trucks

1 Answer

Hi, I have a suzuki swift 2000 model, the key has snapped in the ignition, i have a used replacement ignition barrel and key. When fitted the engine turns over but won't start. I'm guessing th

This car has a chip key, you can't just put any old key in it it must be programmed to not turn on the security system and disable starting, which is what you have now, the system has locked you out.

Feb 10, 2012 | Suzuki Swift Cars & Trucks

1 Answer

The key has broken in the ignition and the lower section of key is stuck in the barrel. The car still starts and runs . How do i remove the broken section of key from the ignition barrel, I have removed...

on the left side of barrel, look for a dowel, there should be a vary small opening that you can take something as small as a pinhead and push the dowel in ,while pushing in on dowel pull the barrel out.the key may need to also be in on position for removal. try that and see if it works. if not please repost your question. thank you for choosing

Dec 30, 2010 | Suzuki Esteem Cars & Trucks

1 Answer


the lock surround has a transponder built into it that recognises the key(you must use the key to start and run the engine)only answer is a new barrel and recode the keys.and no you cannot deactivate the immobiliser........

Jul 05, 2010 | 1992 Volkswagen Golf

1 Answer

I bought a 2000 w reg renualt kangoo, engine was done so i got a clio engine of same year same that engine is changed i cant get a spark 2 engine.ecu ? or wot need the key and barrell from clio engine and the ecu or else bring to dealer to reprograme the ecu to the key

Apr 07, 2010 | 2000 Renault 181

2 Answers

Key broken off in ignition barrel - how do I remove the barrel?

not saying it is landrover barrel but best way is get your new barrel and that should tell you how it is fitted normally a spring loaded pin holds barrel in socket

Mar 20, 2010 | 1994 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides