Question about Cars & Trucks

1 Answer

How can I know that the battry is getting charged as the cng light get stop after 2 mit

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 100 Answers

Use a multi meter to read the current going into the battery. If the voltage drops after the charger light has gone out the it is not charging...

Posted on Apr 18, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What cause battry to die over night?


If test light is a 12 volt light tester AND ILLUMINATES BRIGHT it shows that a component is actively trying to complete a circuit and yes drawing power causing a drain on your battery, now if test light illuminates low, possibility could just be ecm memory or antitheft system active . either way this test should only be done with a 12 volt test light as if you use a 5 volt (computer friendly) tester , false light will have you chasing a ghost. trust me. that trick helps by checking for parasitic draws a 12 volt tester does not illuminate when keep alive memory voltages are present . those voltages are not enough to drain over night. good luck

Nov 28, 2017 | GMC Cars & Trucks

1 Answer

What cause the battry light to stay on when driving?


The battery is not charging. Check the drive belt is not slipping, otherwise it could be an alternator fault.

Nov 03, 2016 | Cars & Trucks

1 Answer

Why are my battry light staying on?


does it stay on when you have driven the car for a few minutes? if you did not drive it , try that

Nov 03, 2016 | Toyota Cars & Trucks

3 Answers

When start the engine all the lights are blinking


NEVER remove the battery cable when the engine is running. It can damage the alternator and a lot of other electronics on the vehicle. The alt will go to the full charge mode. Most all of the dash warning lighs shut off thru a circuit that goes to the alternator. Check your wiring for loose connectors or a grounding wire.

Dec 31, 2013 | 2000 Mitsubishi Montero Sport

1 Answer

I drive a biofuel opel corsa. Last time when i switched from CNG to gasoline to i am getting knocking sound near acceleration pedal. The sound usually comes when i shift from higher gear to lower. for eg...


IF YOU ARE HAVING BRAKES PROBLEMS THEN YOU NEED TO STOP DRIVING VEHICLE... get it check by dealer repair should be covered under warranty
sounds like a computer software problem

May 13, 2017 | Cars & Trucks

1 Answer

I have a 96 s10 blazer with a 4.3 starts hard idles rough wants to stall has misfire and when I turn on the blinker the battery gauge moves with it and when in park if I Rev the motor the speedometer and...


Have you checked the voltage at the batry when running? Sounds like alternator is not working properly. The battry is only used for starting, once started the alternator runs all the accesories & charges the battry. If not chargeing the vehicle will **** battry power. You may have a good battry surface voltage but a bad battry. The battry should be load tested as well.

Jun 24, 2012 | Cars & Trucks

3 Answers

I have a 2002 Chevy Cavalier which also runs on CNG. I went to the fill station and the attendant tried to fill it up. It made a very loud sound and a mechanic came out and said it is probably the release...


If the converter is leaking. you can have it welded, unless it is really rusted bad. If the converter was bad it would have pop a code. effeciency below threshold or 02. There is no need to replace it if you can have it welded. And it can be welded with out harming it.

Jun 28, 2011 | 2002 Chevrolet Cavalier Coupe

1 Answer

When you turn the key nothing happens but the battery shows full charge and all lights, radio etc work. Its a 2002 Mits Galant


hi, the problem you are describing sounds like the starter motor has packed up or a wire might have even come off the back of the starter if your sure the battry is fully charged then the chances are the problem is with the starter motor, that is where i would start looking anyway

Aug 25, 2009 | 2002 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...