Question about Cars & Trucks

Open Question

Hi, I am looking for replacement for the alternator pulley for my Camry NAP but I cant find the exact match. I just wonder is there any replacement, the best match.

VIN code 4T1BF3EK6AU020536 THE ALTERNATOR PULLEY PART NUMBER IS 27415-0W120

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: 1998 audi a4 car stereo

That's weird that they won't help you out. Usually if the stereo is in the car and you show proof of ownership of the vehicle, they'll give you the code for a fee. I'd call another Audi dealer (or a VW dealer - same corporation so they should be able to help) and see if they'll do it for you. Typically they look up the code based on the VIN of the vehicle, but obviously since your stereo was replaced they can't do it that way. Hopefully another dealer will be more understanding of the situation and will help you out. That's the only way to get it though.

Posted on Oct 16, 2008

  • 7 Answers

SOURCE: Our 2001 camry lost power going down the road and

I'm not sure about the belt set up, it should be on a sticker under the hood. But losing your alt can cause the car to die due to loss of electrical power to run the computer, fuel pump, coils, ext. on some cars you can run for awhile on the battery, but eventually it'll die. Some cars are set up to die if the alt fails so that the rest of the cars systems can still be used

Posted on Apr 11, 2010

  • 228 Answers

SOURCE: The serpentine belt pulley just

call a parts place and they can look it up for you, if they carry them. if not try a junkyard

Posted on Dec 16, 2010

  • 10 Answers

SOURCE: I replaced the alternator on my 1990 K1500 w/5.7 L

The whole assebly will rotate allowing the tension to be release. Place breaker bar on nut in front of pulley and rotate... up if i remember right and tension is relieved. If pulley itself is siezed you will now it when the tension is relieved.. Good Luck

Posted on Dec 20, 2010

ftw1952
  • 10319 Answers

SOURCE: i just got my car out the shop, i got a engine

the vin number on the receipt maybe the vin number the used engine came from which is required by law. It shows the engine came from a car not stolen
Its the law to print the vin number on customers receipts for any used parts installed in their cars

Posted on Mar 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tighten the serpentine belt on a 4 cylinder 2003 toyota camry?


Hi Tyrone - those belts aren't going to tighten. They have what is called a tensioner - a pulley - that will flex back and forth so that you can put the belt on and off without tension being on it. You'll move the tensioner, pressure is relieved - you can remove the belt. When you release - it will go back to the extended position. When you put the belt back on - you'll move that pulley again, get the belt in place and slowly release the pulley so that it puts tension back on the belt.

What are the symptoms exactly - is the belt squealing or do you see or feel extreme vibration while the car is running? I'm not sure if I have the tech info on the 2003 Camry - but if that's a serpentine belt there may be other issues. There may be an adjustment on one of the other pulleys - I'll look now. If you can reply with exact symptoms I may be able to help you out. That 19mm bolt you mentioned may be the tensioner pulley bolt. Some have bolts - some have a hole where the tip of a ratchet (3/8" - 1/2") would go - that's how you get the pulley to move.

All The Best, Justin M
17 South Industries, LLC

Here's a link to a quick how to off of Advance A's website:
Serpentine belt replacement

May 28, 2016 | 2003 Toyota Camry

1 Answer

What is the cylinder order for a 4 cylinder toyota camry


It is 1-3-4-2 with No 1 being at the timing belt and crank pulley end.

Jun 09, 2014 | 2001 Toyota Camry

1 Answer

How do you install abelt tension pulley on a 2002 camry


Do yourself a favor and go buy the whole tensioner assembly. Should be about a hundred bucks at a parts store. Yours is 10 years old and the spring in the tensioner is usually the bad part, not the pulley. Since the pulley has bearings however we replace the whole shootin' match.

Open the hood and look around for the little decal which shows a long wrench moving a pulley. That is a clue on how to let tension off the serpentine belt so you can pull it aside. Do as it suggests, you can put a pipe over a regular wrench for more leverage, check with Mr. Archimedes, or you can zip tie a broom handle to it. A shop will have a special longa** wrench. You know this would also be a great time to replace the serpentine belt unless you are sure it has already been replaced.

Take out the three bolts holding the tensioner in, put the new one in via reverse order, put the belt back on and you are done. If you bust a bolt, call a shop and a tow truck as you are screwed.

Sep 22, 2011 | 2002 Toyota Camry

1 Answer

What fuse controls the 12V chargers in a 2008 Camry? I see nothing straightfoward in the fuse box diagram under the hood. "charging system" is the closest match, but I'm suspect that it is linked...


Hi, look for a fuse marked CIG for the lighter. Look for one marked P/POINT or PWR OUTLET for the aux outlets. These fuses may be by the battery or inside the car.
I don't have diagrams for 2008, but these are the labels in the 2006 diagram.

Jan 20, 2011 | 2002 Toyota Camry

1 Answer

How to remove alternator on 1998 camry V6


The bast thing to do if you have to ask how to remove it, is to get a manual for your vehicle. This will provide instructions on removal AND replacement.

First you disconnect the battery from the vehicle (10mm open or socket wrench will do)
The remove the serpentine belt by releasing the tension on the idler pulley. Slide the belt off the alternator pulley.
Disconnect ALL wires (usually plugs) including the ground wire (usually separate) .
Using the appropriate sized tool, remove the bolts holding the the alternator to the accessory frame of the engine.

To install reverse the process EXACTLY. Connect the battery LAST.

Take the old alternator back to the store for the core charge refund.

I still recommend getting a manual for your vehicle.

good luck and don't forget to vote!!!

Sep 28, 2010 | 1998 Toyota Camry

1 Answer

Our 2001 camry lost power going down the road and died. We looked under the hood and the pulley that comes off the engine that runs the alternator belthad came apart. If the pulley came apart and that belt...


I'm not sure about the belt set up, it should be on a sticker under the hood. But losing your alt can cause the car to die due to loss of electrical power to run the computer, fuel pump, coils, ext. on some cars you can run for awhile on the battery, but eventually it'll die. Some cars are set up to die if the alt fails so that the rest of the cars systems can still be used

Apr 11, 2010 | 2001 Toyota Camry

2 Answers

I need the routing diagram for the serpentine belt


there should have been a picture under your hood , but here ya go .

dc8b3a4.jpg

Jan 08, 2009 | 2003 Toyota Camry

1 Answer

On an 02 2.4l camry how do u change the serpentine belt


Hi Nick,
  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Nov 12, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...